On your 17mm and 20mm fet-only drivers it shοuld be working as is . Just saying 
Not necessarily. The mode switch timing may be off, the LVP will definitely be off. It would run, but it wouldn't be right.
Of course . These need quite some time , test - reprogram - test again , and you have to do it for a lot of different drivers …
Hi all. Approximately how long would it take between ordering and shipping if I order three MTN, FET+7135 drivers? (These are in stock at the moment.) I ask because I have a small window where I can ship to a friend in the US and if that can’t happen, I’ll have to ship to a different address which will take a month or so to get to me. Hahahahh!
Thanks! 
If you ordered today they should ship tomorrow, unless you want something custom like custom firmware (that might take until Monday or Tuesday).
I have to hand it to Richard, and family. I have never had an order not ship next day, except maybe Sunday :+1: and some ship same day.
Do you know how long shipping to Germany takes normally, I ordered 2 XHP35 Hi on 8. Dez. and nothing received yet
LOVELY!! Thanks Rich!
Usually 1-3 weeks. You can check the tracking number you received along the way, although looking at the tracking your package has taken the long route there. Unfortunately, there is nothing we can do to speed things up once the post has the package.
Hi,
do you still offer Qlite drivers with guppydrv V2 firmware? I need a driver with “Strobe only” but on your website only V1 is listed.
Regards
Kenjii
No. They were never offered with any other guppydrv than what you see listed.
Morning Richard. I sent a PM with a request. I apologies for the terrible timing. :person_facepalming:
I know it’s not quite the same, but guppydrv’s Group #9 is Strobe - 100%, no memory. If you used that, the light would come on in Strobe mode all the time, and could then also be used as a flashlight if needed.
I think i found what i searched for. An old FET driver has the option for guppydrv Rev. 2. I am going to order that one instead of the Qlite.
Richard, do you have an idea when you’ll get more 22ga silicone wire in stock? Your listing says you only have 3ft remaining, and I need more than that.
I've been sicker than a dog today 
, but when I get out there tonight I'll check and see if I have any extras laying around (I usually keep some extras in case I need some for drivers or lights!)
Thanks Richard. I hope you get to feeling much better soon! I was looking to buy about 10 feet. I need a couple lengths of 3 feet at a minimum. So, if you have even one more piece of 3 feet or more, plus what’s listed as three feet, I could do with that for now.
Richard - do you plan on getting more SupFire L5's? I see only 1 is available and it's modded. SupFire shows a 3rd generation of this light on their website now - shame because I like the 2nd gen you had better. They added a lit switch and USB charging - both popular now.
The SupFire L5 is only available very limited in retail, and rather pricey, and mostly listed as the gen 1.
Gen 1: better finishing with true flat anodizing, but the switch is so-so
Gen 2: went to an SRK style metal switch - I like much better, but the finish when to a plainer, cheaper look
Gen 3: changed switch once again with LED's behind it, added USB charging. Not sure of anodizing.
Here is Gen 3: http://www.supfireenglish.com/Products/led_flashlight/medium_flashlight/2016/1231/128.html
Here is Gen 2: http://www.supfireenglish.com/Products/led_flashlight/medium_flashlight/2014/0613/52.html
Not that you have a choice in the matter but I hope you get well soon. The most disgusting but effective treatment I can reccomend is a sinus rinse to flush out the bugs, yecch!
Just added some 22 awg wire.