Itās just a disastrous shame they didnāt make them 2 mm x 12 mm. Theyāre slightly smaller than that, so itās hard to find trits that fit. FAIL
Yea I checked around too - wut a disaster... Made trit slots for trit sizes that don't exist.
Damn. Now What?..ā¦
Use smaller ones and center it?
My RRT-01 is reported shipped by BG
:beer: yay!
Mine is shipped too. Now I hope my new LEDs for this light arive in time.
which LED are you planning?
Got in on this. Thanks. Saved me some money.
Was in doubt to use 219b sw40 9080. But decided to with 3000k sst-20 95cri.
Damn. Now What?..ā¦
Tom E:Yea I checked around too - wut a disasterā¦ Made trit slots for trit sizes that donāt exist.
Over on CPF, one guy posted about using a Dremel and boring out the slot ends just a little to make 12mm work. So Iām assuming the thickness is OK.
Damn. Now What?..ā¦
Tom E:Yea I checked around too - wut a disasterā¦ Made trit slots for trit sizes that donāt exist.
Over on CPF, one guy posted about using a Dremel and boring out the slots just a little to make 12mm work. So it wasnāt just the length but the thickness and depth that required trimming.
for a while, this light was the main news! So many others being offered up now
My RRT-01 is reported shipped by BG
Same!
Still waiting to hear why my BG order was secretly cancelled.
optosolis:Damn. Now What?..ā¦
Tom E:Yea I checked around too - wut a disasterā¦ Made trit slots for trit sizes that donāt exist.
Over on CPF, one guy posted about using a Dremel and boring out the slots just a little to make 12mm work. So it wasnāt just the length but the thickness and depth that required trimming.
I put up some pics of the trit slots ground out to fit the 2x12mm trit vials a few weeks ago. WTB: Jetbeam RRT01 ā Any place to buy it?! + [RRT01 2019 discussion] - #261 by moderator007
Itās either grind the slots to fit 2x12mm or use smaller trit vial. I never had any luck finding 2x10mm even though they do exist.
xevious: optosolis:Damn. Now What?..ā¦
Tom E:Yea I checked around too - wut a disasterā¦ Made trit slots for trit sizes that donāt exist.
Over on CPF, one guy posted about using a Dremel and boring out the slots just a little to make 12mm work. So it wasnāt just the length but the thickness and depth that required trimming.
I put up some pics of the trit slots ground out to fit the 2x12mm trit vials a few weeks ago. WTB: Jetbeam RRT01 ā Any place to buy it?! + [RRT01 2019 discussion] - #261 by moderator007
Itās either grind the slots to fit 2x12mm or use smaller trit vial. I never had any luck finding 2x10mm even though they do exist.
Good to know that, thanks. There are 1.2 mm x 5 mm tritium vials available. So you could stack 2 of them in a slotā¦ but will look a bit thin.
Yea I checked around too - wut a disasterā¦ Made trit slots for trit sizes that donāt exist.
JB never mentioned the slots are for trits. Could be just coincidental ornaments
[Clemence]
BTW Martin, sent you PM regarding my order which is on hold. BG couldnāt ship it to my address (after 2 weeks processing time waits) and asked me for extra shipping cost without telling me how much the extra would be. Just asked me a yes or no confirmation
[Clemence]
PMed you