FW3A, a TLF/BLF EDC flashlight - SST-20 available, coupon codes public

12716 posts / 0 new
Last post
tatasal
Offline
Last seen: 20 min 4 sec ago
Joined: 02/15/2012 - 08:40
Posts: 5050
Location: Far East
ToyKeeper wrote:
tatasal wrote:
here’s some off-topic plug of a 26650 … The Shockli

Just to clarify for people in the FW3A group buy, this battery does not fit into the FW3A. It’s completely unrelated.

So sorry for that. l carelessly posted it here, originally intended for the FT03 (which can use a 26650) gb thread: Facepalm

ToyKeeper
ToyKeeper's picture
Online
Last seen: 8 min 7 sec ago
Joined: 01/12/2013 - 14:40
Posts: 9656
Location: (469219) 2016 HO3
contactcr wrote:
People have made dozens of 219b fet triples not sure why the sudden concern with a mid drain battery?

If I recall correctly, the old 219B emitters may have had higher Vf than the more recent ones, so the more recent ones are more prone to turning into smoke.

But mostly, I think it’s just because people are more concerned with general safety now, after reports of some Fireflies lights damaging their 219B emitters.

So… I’ll just make a 219 build for the FW3A firmware. It could either have the FET turned off entirely (max output of ~800 lm), or it could have the FET levels decreased to like 25% or 33% or 50%. Not sure which would be better.

trakcon
trakcon's picture
Online
Last seen: 14 min 21 sec ago
Joined: 01/23/2019 - 15:50
Posts: 133

Thanks for the explanation, zak. I need to brush up on my electronics. It’s been a while.

And, thank you, again, TK.

Mike

JaredM
JaredM's picture
Offline
Last seen: 2 days 9 hours ago
Joined: 10/31/2011 - 13:33
Posts: 575
Location: Pittsburgh, Pennsylvania
ToyKeeper wrote:
contactcr wrote:
People have made dozens of 219b fet triples not sure why the sudden concern with a mid drain battery?

If I recall correctly, the old 219B emitters may have had higher Vf than the more recent ones, so the more recent ones are more prone to turning into smoke.

But mostly, I think it’s just because people are more concerned with general safety now, after reports of some Fireflies lights damaging their 219B emitters.

So… I’ll just make a 219 build for the FW3A firmware. It could either have the FET turned off entirely (max output of ~800 lm), or it could have the FET levels decreased to like 25% or 33% or 50%. Not sure which would be better.

TK. You’re the best! BLF wouldn’t be what it is without ya!

goshdogit
goshdogit's picture
Offline
Last seen: 2 hours 4 min ago
Joined: 12/03/2015 - 21:28
Posts: 929

ToyKeeper wrote:
So… I’ll just make a 219 build for the FW3A firmware. It could either have the FET turned off entirely (max output of ~800 lm), or it could have the FET levels decreased to like 25% or 33% or 50%. Not sure which would be better.
Nice! I’ve got a 219B triple board waiting for my FW3A.

I’ve been tempting fate with 219B emitters in a D4. I have the ramp ceiling turned way down and mostly use it on lower levels, but I’ve run it on turbo for a few seconds a handful of times. Party

Will the FET % be a compile option, or something you determine during testing? BTW, I’ll gladly send you a 219B sw45k R9080 triple board if you need/want one for your FW3A.

PleinPhare
Offline
Last seen: 9 hours 25 min ago
Joined: 01/22/2016 - 00:18
Posts: 43
Location: California

Time to jump…
Please add me to the list for one !

Thanks

teejay
Offline
Last seen: 3 hours 34 min ago
Joined: 02/26/2019 - 12:03
Posts: 10
Location: Boise, ID

I’m interested in one.

KevinZA1988
KevinZA1988's picture
Offline
Last seen: 4 hours 16 min ago
Joined: 02/26/2018 - 02:26
Posts: 437
Location: South Africa

I would really like it if the ramp has an indication of when it goes from regulated to hybrid modes like the Emisar D4 standard UI. Or if there’s a pre-defined percentage indication in a leaflet that allows one to adjust the ramp ceiling to max regulated current, leaving turbo for full FET.

Would this be possible?

Acebeam L16, BLF Q8, BLF A6, BLF FW3A, BLF FW3C, Convoy L2, Convoy L6, Convoy C8+ , Convoy S3, Convoy M21A, Convoy S11, Emisar D4, Jaxman E2L, Olight S1R Baton II special edition series, S2R Baton II, Nitecore HC65, Olight H1R Nova.

ToyKeeper
ToyKeeper's picture
Online
Last seen: 8 min 7 sec ago
Joined: 01/12/2013 - 14:40
Posts: 9656
Location: (469219) 2016 HO3

goshdogit wrote:
Nice! I’ve got a 219B triple board waiting for my FW3A.

I’ve been tempting fate with 219B emitters in a D4. I have the ramp ceiling turned way down and mostly use it on lower levels, but I’ve run it on turbo for a few seconds a handful of times. Party

Will the FET % be a compile option, or something you determine during testing? BTW, I’ll gladly send you a 219B sw45k R9080 triple board if you need/want one for your FW3A.

The FET percent is generally just a hardcoded thing. I’m just not sure yet what percent it should be. I’ll probably put in a few options which can be selected at compile time, and make the default build something relatively safe. I definitely can’t turn down a 219B triple board though; those are hard to get these days.

ToyKeeper
ToyKeeper's picture
Online
Last seen: 8 min 7 sec ago
Joined: 01/12/2013 - 14:40
Posts: 9656
Location: (469219) 2016 HO3

KevinZA1988 wrote:
I would really like it if the ramp has an indication of when it goes from regulated to hybrid modes like the Emisar D4 standard UI. Or if there’s a pre-defined percentage indication in a leaflet that allows one to adjust the ramp ceiling to max regulated current, leaving turbo for full FET.

Would this be possible?

It’s too late to change the firmware now, but fortunately that function is already included. It has a brief blip in the ramp when it changes power channels.

About the actual ramp shape, those values are in the config file. They’re also in the user manual.

KevinZA1988
KevinZA1988's picture
Offline
Last seen: 4 hours 16 min ago
Joined: 02/26/2018 - 02:26
Posts: 437
Location: South Africa

ToyKeeper wrote:
KevinZA1988 wrote:
I would really like it if the ramp has an indication of when it goes from regulated to hybrid modes like the Emisar D4 standard UI. Or if there’s a pre-defined percentage indication in a leaflet that allows one to adjust the ramp ceiling to max regulated current, leaving turbo for full FET.

Would this be possible?

It’s too late to change the firmware now, but fortunately that function is already included. It has a brief blip in the ramp when it changes power channels.

About the actual ramp shape, those values are in the config file. They’re also in the user manual.

Awesome, thanks ToyKeeper!

Acebeam L16, BLF Q8, BLF A6, BLF FW3A, BLF FW3C, Convoy L2, Convoy L6, Convoy C8+ , Convoy S3, Convoy M21A, Convoy S11, Emisar D4, Jaxman E2L, Olight S1R Baton II special edition series, S2R Baton II, Nitecore HC65, Olight H1R Nova.

Relampago
Relampago's picture
Offline
Last seen: 1 hour 23 min ago
Joined: 04/14/2019 - 11:44
Posts: 408

In for 1 please!

“Electricity is really just organized lightning”
― George Carlin

goshdogit
goshdogit's picture
Offline
Last seen: 2 hours 4 min ago
Joined: 12/03/2015 - 21:28
Posts: 929

ToyKeeper wrote:
I definitely can’t turn down a 219B triple board though; those are hard to get these days.
Great! PM sent.
matik42
Offline
Last seen: 6 hours 21 min ago
Joined: 06/03/2016 - 15:53
Posts: 101
Location: Estonia

Please take me (1690) off the list.

Thanks

clip.
Offline
Last seen: 1 month 1 week ago
Joined: 03/19/2019 - 11:31
Posts: 40

Interested in two four, is the “group buy” list still open?

Looks like a perfect EDC.

tatasal
Offline
Last seen: 20 min 4 sec ago
Joined: 02/15/2012 - 08:40
Posts: 5050
Location: Far East
clip. wrote:
Interested in two, is the “group buy” list still open?

Yes, and as many as you wish.

mortuus
mortuus's picture
Offline
Last seen: 2 hours 57 min ago
Joined: 12/16/2014 - 09:33
Posts: 1899
Location: Sweden

have the samples to people been sent out, will we hear anything from them?

...where Frugal meets with Flashlight!

tatasal
Offline
Last seen: 20 min 4 sec ago
Joined: 02/15/2012 - 08:40
Posts: 5050
Location: Far East
mortuus wrote:
have the samples to people been sent out?

The reply today from people in the know was: “Should be tomorrow”

Martinc5618
Offline
Last seen: 1 week 1 day ago
Joined: 11/23/2018 - 18:31
Posts: 2
Location: Melbourne Australia

Put me down for one too please.

MokrySedeS
Offline
Last seen: 12 hours 1 min ago
Joined: 10/14/2018 - 06:17
Posts: 16
Location: Poland

Can I call dibs on one more (total of 3) but only with samsung emitters (if they show up eventually)? Would it still be as part of the group buy?
Also, I’d really like to have an option to have the bunny on the switch Blushing

tsouzee
Offline
Last seen: 3 weeks 1 day ago
Joined: 03/09/2019 - 08:00
Posts: 21
Location: NY

How do we get put on the list to order? Do we need to PM someone in particular?

MascaratumB
MascaratumB's picture
Online
Last seen: 3 min 43 sec ago
Joined: 10/29/2016 - 12:12
Posts: 3699
Location: Portugal

tsouzee wrote:
How do we get put on the list to order? Do we need to PM someone in particular?

You can declare your intention here on the thread of how many lights you’ll want! When the interest list is updated, you’re name will be on it! Beer

[REVIEWS] AMUTORCH: S3 / S3 vs 219c / AM30 / AX1 / VG10 /// SOFIRN: SF14 & SP10A / SP32A / SP10B /// NITEFOX: UT20 / ES10K / K3 /// ODEPRO: KL52 / B108 /// ACEBEAM: H20 /// BLITZWOLF: BW-ET1 /// DQG: AA Slim Ti /// HC-LIGHTS: SS AAA /// XTAR: PB2 Charger /// OLIGHT: M2R Warrior /// WUBEN: TO10R / E05 / T70 / E10 /// ON THE ROAD: M1 / i3 / M3 Pro /// ROVYVON: A2 & A5R / E300S / A8 /// KLARUS: XT1C /// LUMINTOP: Tool AA V2.0 & Tool 25

Tricks: 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 /// TIR Lenses:1 / 2 /// Others: Biscotti 3 & 1*7135 / Triple TIR & XP-G2 ///// My Collection ///// My Review's Blog (PT)

GIVEAWAY: 1

 

SKY69
Offline
Last seen: 21 hours 47 min ago
Joined: 11/13/2018 - 17:41
Posts: 105

Just checking on addition status. I added one more to the first one #1648 however have not seen a change on the interest list to two total. Just don’t want to miss out.

MascaratumB
MascaratumB's picture
Online
Last seen: 3 min 43 sec ago
Joined: 10/29/2016 - 12:12
Posts: 3699
Location: Portugal

SKY69 wrote:
Just checking on addition status. I added one more to the first one #1648 however have not seen a change on the interest list to two total. Just don’t want to miss out.

The list wasn’t updated yet!
If you go to the first page and check the list, always seek the last name on that +2000 names list.
If you click in the the last one you’ll see when the list was updated last time. Then you’ll only have to check/know when you made your request.
In this case, you’ve requested on the 16th March, but the list was only updated until the 11th March!

When ToyKeeper / FW3A Team has the time for it, the list will be updated Beer

[REVIEWS] AMUTORCH: S3 / S3 vs 219c / AM30 / AX1 / VG10 /// SOFIRN: SF14 & SP10A / SP32A / SP10B /// NITEFOX: UT20 / ES10K / K3 /// ODEPRO: KL52 / B108 /// ACEBEAM: H20 /// BLITZWOLF: BW-ET1 /// DQG: AA Slim Ti /// HC-LIGHTS: SS AAA /// XTAR: PB2 Charger /// OLIGHT: M2R Warrior /// WUBEN: TO10R / E05 / T70 / E10 /// ON THE ROAD: M1 / i3 / M3 Pro /// ROVYVON: A2 & A5R / E300S / A8 /// KLARUS: XT1C /// LUMINTOP: Tool AA V2.0 & Tool 25

Tricks: 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 /// TIR Lenses:1 / 2 /// Others: Biscotti 3 & 1*7135 / Triple TIR & XP-G2 ///// My Collection ///// My Review's Blog (PT)

GIVEAWAY: 1

 

Rando
Offline
Last seen: 1 week 4 days ago
Joined: 03/14/2019 - 22:53
Posts: 16
Location: US

Please put me in for a second one (first one was in post 7778).

Prefer Cree XP-L HI (both)

Thanks.

teacher
teacher's picture
Offline
Last seen: 28 min 30 sec ago
Joined: 02/23/2016 - 19:04
Posts: 9374
Location: NE & SW Alabama

Please add me for two (‘2’) more….. for a total of 6.

Thank you. Beer

You never know how a horse will pull until you hook him up to a heavy load./"Bear" Bryant 

 .................................. "Slow is Smooth, Smooth is Fast" ...................................

       Texas Lumens Flashlights / M4D M4X Deals : sign up - save $$$$  

         Rudeness Level _ mΩ _ {width:70%} _ LightWiki _ LED Tint Chart  

      Xlamp size chart _ BatteryU _ Flashaholic? Need Professional Help???            TheOriginal _ TAB _ LightSearch _ BatterySearch _ 14500's _ DiCal 

 

                                             

SKY69
Offline
Last seen: 21 hours 47 min ago
Joined: 11/13/2018 - 17:41
Posts: 105

Thanks MascaratumB for the info. As excited as I am I also have plenty of patience for this light especially considering all the brilliant people who have donated their time and expertise to this project.

FMcamaroZ28
FMcamaroZ28's picture
Offline
Last seen: 2 months 7 hours ago
Joined: 10/08/2012 - 09:05
Posts: 972
Location: New Jersey

Put me down for one as well please!

ottrocity
ottrocity's picture
Offline
Last seen: 2 months 3 weeks ago
Joined: 04/16/2019 - 15:43
Posts: 1

Put me down for two!

tatasal
Offline
Last seen: 20 min 4 sec ago
Joined: 02/15/2012 - 08:40
Posts: 5050
Location: Far East

Three samples shipped to testers.

Pages