I’m gettin’ antsy for an ‘accessories’ video, Den!
Here are this week’s additions to the interest list and the files linked to in post #1 have been updated.
To this point we have 2,439 on the interest list.
Thanks
2453 belit
2454 dsd64
2455 Atypicallemon
2456 treadhead71
2457 Ashy Flashy
2458 Ashy Flashy
2459 marcelangelo
2460 Not_Dave
2461 gavrook
2462 Sopuchan
2463 nicois
2464 redblue
2465 casi29061965
2466 PTRCK
2467 abbazaba
2468 Bibendum
2469 Bibendum
2470 Hollywood88
2471 obriencr
2472 bradmck
2473 SDS
2474 lunchbox
2475 atobe
2476 sueli428
2477 Gerrh
2478 Gerrh
THIS! ^
Need. Video. … Must. Have. More.
I know, give them something great and they only want MORE!
I am in for at least 3 accessory kits that include every add on discussed in this thread. A molded carrying case is a must have for this thing to live up to its potential as the most awesome lantern ever offered.
I’m working on the accessories I been quite overloaded with errands & work lately, but will try to get a video done in a week or two and post to my channel.
Oh dang candy orange would be awesome !
As far as I’m aware, all of Lexel’s drivers use a single pogo pad layout.
All of Emisar’s lights use a consistent pad layout too, ever since Emisar started adding pads (D4v2 and newer).
However, those are two different layouts.
HarleyQuin’s HQ Universal ProgKey works on both, but it’s necessary to move a couple wires to change the mapping when switching back and forth. This isn’t commercially available though; people basically have to build their own or find someone who makes them.
Emisar’s flashing kit uses a 4x2 layout, but the 2 unused pins are omitted, so it doesn’t work with Lexel’s 3x2 layout. At least, not without soldering on another pin or two.
So… long story short: The BLF LT1 Lantern has programming pads for updating the firmware, but no adapters for it are commercially available yet.
This lack of compatibility is very disheartening.
Any outlook for standardizing something and keeping to that in the future?
Agro:Candle mode runs the lantern with the last selected output level and tint right?
All modes share the same color temperature / tint setting. It can be ramped in almost any mode, by doing a “click, click, hold”.
Candle mode has its own brightness level, configured by holding the button to ramp up/down.
Do you think it would make sense to run the candle always on the warmest level regardless of the pre-set tint?
Interested
I’m interested in one!
Any outlook for standardizing something and keeping to that in the future?
That mostly depends on getting people to cooperate, and getting companies to cooperate. And that’s … difficult.
Do you think it would make sense to run the candle always on the warmest level regardless of the pre-set tint?
Not really. However, you could use one of the auto-tint modes to get a somewhat similar effect.
Interested
I’m interested in one.
I’ve been lurking for years and just signed up to get on the list for one! Very interested.
eugene188:… dude pulling out a pink or bright purple light……
Dangit - if we can get a purple TK edition FW3a, we should be able to get a purple LT1!
Though, TBH, I’d love a candy orange or dayglow yellow or fluorescent lime green or dazzling red a lot too. My wallet though - not so much.
HOLY damn those colours! Candy Orange?? Lime Green?? YES!
It’s like people who paint their cars ridiculous colours. I hate it, but I love it so much.
amishbill: eugene188:… dude pulling out a pink or bright purple light……
Dangit - if we can get a purple TK edition FW3a, we should be able to get a purple LT1!
Though, TBH, I’d love a candy orange or dayglow yellow or fluorescent lime green or dazzling red a lot too. My wallet though - not so much.
HOLY damn those colours! Candy Orange?? Lime Green?? YES!
It’s like people who paint their cars ridiculous colours. I hate it, but I love it so much.
I’ve been told that if I get the lime green Charger Daytona I was looking at, I’ll also be getting a divorce. I think I can get away with another light (or 3). But then again, it IS a nice car….
Man, I saw this back in the very early stages, but I haven’t been around for a while. Turned out really nice.
Is it still possible to get on the list for two?
Thanks…
Man, I saw this back in the very early stages, but I haven’t been around for a while. Turned out really nice.
Is it still possible to get on the list for two?
Thanks…
Nope not too late. I added you for 2.
sorry, may I also have 2 lanterns? thanks!
@Toykeeper: Can you please confirm that the UI chart (see ► here ◄) for the LT1 lantern is the final version? Sofirn sent me the (English) manual for translation today. I presume they will ship the initial batch with the English version only and include multi-language manuals in later batches. I intend to incorporate your nice UI chart into the updated manual (both English and German) that I also plan to host on my Sofirn sharepoint on Google Drive. If all works out as planned the manual might be able to download in two weeks from now.
Cheers,
Thomas
@Toykeeper: Can you please confirm that the UI chart (see ► here ◄) for the LT1 lantern is the final version? Sofirn sent me the (English) manual for translation today. I presume they will ship the initial batch with the English version only and include multi-language manuals in later batches. I intend to incorporate your nice UI chart into the updated manual (both English and German) that I also plan to host on my Sofirn sharepoint on Google Drive. If all works out as planned the manual might be able to download in two weeks from now.
Cheers,
Thomas
:+1: it is the correct one as far as i know.
Lux-Perpetua:@Toykeeper: Can you please confirm that the UI chart (see ► here ◄) for the LT1 lantern is the final version? Sofirn sent me the (English) manual for translation today. I presume they will ship the initial batch with the English version only and include multi-language manuals in later batches. I intend to incorporate your nice UI chart into the updated manual (both English and German) that I also plan to host on my Sofirn sharepoint on Google Drive. If all works out as planned the manual might be able to download in two weeks from now.
Cheers,
Thomas
:+1: it is the correct one as far as i know.
Do we want to sub in the production logo (your B&W or my colorized) or am I being too OCD on it?