What you got today

Need 4 actually!!! haha, one pair for voltage and current at each end of the driver...

I was happy i recieved a notice to pick soemthing form post office but turend out to be "just" neodymium magnets. Still pretty fun to play with. Those are not for me but nonetheless i will play a little with them. Feeling like a 5y old kid.

Getting spoilt with expecting flashlights with each package....

Just arrived, a rather odd light from DX. Apparently it is designed for examining jade and jewellery.

First impression, it's very heavy (178g with a cell)

Second impression is that the beam is pretty good but very, very warm. Review to follow.

Looking very good i must admit.

For those who are waiting for some package try this to ease the wait.

3 Sipik SK68 from Focalprice . It was a weekend deal and I payed a total of 24.48$. They have all XR-E LEDs (!). I ordered them 03-05-2011 and they arrived yesterday at the post office. So far I just tested them quickly with a Alkaline battery and they all work fine. Two of them look quit nice, but the third one is a bit scatched, despit all came in bubble wrap and card board boxes. I'm still satisfied with the deal.

I picked them up today. The post office is 35 minutes away by car. I think invironment friendly. Unless there isn't any other good reason to take the car, usually I don't go there just to get three Sipiks. There are exeptions of that rule though. The arrival of the first C8 XM-L was reason enough to kill some trees. I'm sure most of you would agree.

I also have got five 16-mode drivers (1000mA) from KD along with one 8xAMC driver board. I ordered these 02-11-2011.

OMG.... Wasted an afternoon doing useless clicking...

Knowing KD, probably not. Their specs tend to be less than useful. I'd guess, like mine it is intended for jade and jewellery examination.

Just arrived, a rather odd light from DX. Apparently it is designed for examining jade and jewellery.

First impression, it's very heavy (178g with a cell)

Second impression is that the beam is pretty good but very, very warm. Review to follow.

Added beamshots beside an XM-L in an HS-802 thrower.

With the beam shroud on. The XM-L beam is not that blue and green horror shown here - the camera's white balance was trying hard. There was no other light on the ceiling. The beam is heavily reduced by the shroud.

Shroud removed

I received my 763 from Exduct today. It arrived sharp enough to shave hair from my arm! Lockup is tight without any vertical or side to side movement. It is a little stiff to open by just pushing the thumb stud. But releasing the lock allows it to open with a flick of the wrist. Being a lefty, the first thing I did was move the clip to the other side. With the clip holding my jeans pocket firmly against the textured G10, there is no way the knife is going anywhere by accident. The G10 combined with the nice jimping make it unlikely to slip from my hand even when wet. I'm quite happy with the 763 and may get another one.

It's not that they don't realise there is a diffrence, it's more that they don't care what the law is at all.

This is long an rambeling and probably best ignored...you have been warned! :P

While I do have a TV it's not been used as one ever - it's connected to a DVD player and the like, so I don't need a licence.

I used to get letters every couple of months telling me I had to have a licence. Their letters are terribly presumptive and are written as if they know you watch TV.

About once a year I would phone them up pointing out that you are not actually allowed to threaten people with undue legal action and that would be the end of the letters for a while.

Four years ago a disgustingly arogant TV licensing goon banged on my door, I wasn't feeling great so I ignored it. Then she started banging on the window and shouting "HELLO...HELLO" .

She said who she was, I told her the situation and then closed the door...more banging. So I opened it and asked her what on earth she wanted, she shouted that they were going to take me to court unless I paid up or let them "inspect" my house. She ranted some more and then back to the idle threats. I informed her that I was withdrawing her implied right of access and that if she didn't leave immediately I'd have her arrested, I closed the door on her.

I then emailed the TV licensing and the BBC complaints department informing them of their removed rights and that it would apply to any agents acting on their behalf. TV licensing sent an apologetic confirmation and that's the last I heard from them.

Thanks for the photos and review photon1k! It makes me all the more excite to receive mine :D

Today I got a shipment from KD with a neutral white XP-G R4, some 18mm isolator disks, and 5 of the new 1400mA 5-mode driver. The 18mm disks are too big for a P60, but I can trim them down as needed. I was able to convert the driver to 3 modes so that it is just like the Shining Beam driver. Then I'll put these in the Ultrafire X1 I just got and have a nice 3-mode neutral compact 18650.

You're quite welcome. I've got a couple two other SRMs on the way. I'll post pics when I get them.

What a coincidence.

I have got today the same XP-G R4 neutral white and some 16 mm insulator disks.

http://www.kaidomain.com/ProductDetails.aspx?ProductId=1745.

I have got also 5 driver boards, not 1400 mAh but the new 1560mAh 5-mode version.

http://www.kaidomain.com/ProductDetails.aspx?ProductId=11218

i receved my box of 3 safe-lights

My SHININGBEAM envelope came today. I received an ITP A3 EOS. What a great light. Its really pretty impressive how nice the output is. I am ordering some 10440s tonight. There are mixed reviews out there on how this light will handle 10440s. I don’t want to wreck it but I want as much output as possible. Anyone have any firsthand experience running this light on a 10440?
I was going to put this light on my keychain but I have never really liked extra stuff on my keys and didn’t like it on there right away. The clip is really nice so I think it has found a home clipped to the shirt pocket of my uniform.

I got the same drivers. I measured 1450mA, so I'm not sure why they call it 1560. I was very happy to find they can be switched to 3 modes. Let us know if you're able to get any other mode groups out of it. It's probably just a matter of connecting the correct pins, but I would bet it has 4 mode groups like other NANJG drivers.

I was afraid to buy the 16mm disks without a picture. Are they white cardboard with sticky backs? Don't know why KD can't post a picture.

I haven't put my neutral in a light yet, but I did hook it up to my driver to do some testing and it seemed pretty cool white to me. I'm hoping it will look more neutral in a light. This is my second, so I can compare it to the first one I got which was definitely neutral.

That light kicks all kind of butt on 10440 (80 lumens on NiMH, maybe 200 lumens on 10440 and that's with the Q5). I wouldn't leave it on for long on High though as it gets hot pretty fast. And it will wear out those 10440's pretty quickly (not just discharge them, which it will do in 10-15 minutes, but wear them out; I'm on my second set now). Make sure you get the unprotected ones because the protected ones are too long to fit. I keep mine on my keychain and like the lobster claw to quickly remove it from my keys when I need to. I like the clip, but I took it off since I'm using the keychain anyway.