WTB: In need of LED on 10mm copper MCPCB fast.

6 posts / 0 new
Last post
Mike C
Mike C's picture
Offline
Last seen: 10 hours 5 min ago
Joined: 01/22/2014 - 08:03
Posts: 1631
Location: Sweden
WTB: In need of LED on 10mm copper MCPCB fast.

I have a dual LED headlamp project I’m putting together before my vacation in two weeks, and realized that one of the LEDs has to be on a 10mm MCPCB. Anyone have one to sell? Preferable in Europe so it doesn’t get stuck in customs. The other LED (or LEDS on quad) is XP-L HI V3 3C, so I’d hope to get as close to that tint if possible. But beggers can’t be choosers, I’ll take what I can get and replace later, I just want this headlamp working for my 2 months vacation starting in 2 weeks.

kiriba-ru
kiriba-ru's picture
Offline
Last seen: 1 hour 1 min ago
Joined: 01/17/2016 - 02:34
Posts: 1036
Location: Russia

I wonder if you dont have any 16mm sinkpads (which can be cutted/sanded to 10mm).

Meanwhile in Russia: https://twitter.com/CrazyinRussia

djozz
djozz's picture
Online
Last seen: 18 sec ago
Joined: 09/07/2012 - 17:04
Posts: 10386
Location: Amsterdam

I have 4 XM 10mm Sinkpads leftover, but no XP version anymore. So if you could fit an XM-L in your headlamp (you were not fussy, right? Wink ), I can reflow one for you, I’m sure I have one close enough to 3C.

Does anyone know btw who still sells 10mm XP Sinkpads?, it seems that everyone is sold out.

Lexel
Lexel's picture
Offline
Last seen: 1 hour 16 min ago
Joined: 11/01/2016 - 08:00
Posts: 2145
Location: Germany

I have one 10mm Sinkpad for XPL footprint

there is a XP-G2 of a Jetbeam Jet-1 MK dedomed on it

Mike C
Mike C's picture
Offline
Last seen: 10 hours 5 min ago
Joined: 01/22/2014 - 08:03
Posts: 1631
Location: Sweden

kiriba-ru wrote:
I wonder if you dont have any 16mm sinkpads (which can be cutted/sanded to 10mm).

Thanks, but no thanks. I’m not rich, but I earn too much to do that. I’d rather order one from RMM and pay express courier costs than sand down a 16mm.

djozz wrote:
I have 4 XM 10mm Sinkpads leftover, but no XP version anymore. So if you could fit an XM-L in your headlamp (you were not fussy, right? Wink ), I can reflow one for you, I’m sure I have one close enough to 3C.

Life saver! If you are willing to sell a couple I’d be glad to buy two. XM-L is fine, actually preferable if the tint is the same as this LED is going to be a flooder.

Lexel wrote:
I have one 10mm Sinkpad for XPL footprint

there is a XP-G2 of a Jetbeam Jet-1 MK dedomed on it


Thanks for the offer, but in this case djozz’s XM-Ls sound like a better choice. However, if he can only part with one I’ll take it as a backup.
Mike C
Mike C's picture
Offline
Last seen: 10 hours 5 min ago
Joined: 01/22/2014 - 08:03
Posts: 1631
Location: Sweden

Lexel wrote:
I have one 10mm Sinkpad for XPL footprint

there is a XP-G2 of a Jetbeam Jet-1 MK dedomed on it


Actually, I’d like to take it regardless. I just checked and XM-L might be a little too large for the lens of the headlamp. I have a few XP-L LEDs so I can reflow it. Sending PM.

Still want to get from djozz also so I can keep options open as I can probably open up the lens a little. It’s the small lens on the lower right side: