CRX Copper Tube Light III

6 posts / 0 new
Log in or register to post comments
Last post
Wed, 10/10/2018 - 19:43
#1
CRX
CRX's picture
Offline
Last seen: 3 hours 34 min ago
Joined: 04/02/2013 - 15:27
Posts: 3912
Location: Scotland
CRX Copper Tube Light III

CRX Copper Tube Light III - XP-G2 3D - Dual Mode - 10440 - RV Clicky Sw - 140lm.Cree XP-G2 S4 3D emitter
2 Mode driver
Sputnik 10mm TIR
Green GITD bezel
Copper shell & battery sleeve core
Copper & glass reverse clicky switch cover
Rubber switch boot
6mm x 1.5mm green tritium vial
Length – 70mm
Width – 15mm
Weight – 49g (with 10440 cell)
Max – 116lm/ 44lm low

I made this light from some 15mm plumbers tube, copper sheet and other bits & pieces from the parts box.
The reverse clicky switch has a rubber switch boot under the copper & glass cover with a green tritium vial installed.
Two mode, high/ low operated by tightening or loosening the tail after switching on.
Built around a 10440 protected cell.CRX Copper Tube Light III - XP-G2 3D - Dual Mode - 10440 - RV Clicky Sw - 140lm..

 

Copper flashlights

—

- LEDs & Other Stuff - - UI CheatSheets - - CRX Mods & Builds - - Stuff for Sale -  - The Old Lumens Flashlight Modders & Builders Challenge is Now Open - Link -

Edited by: CRX on 10/10/2018 - 21:12
Top
Wed, 10/10/2018 - 19:45
travis
Offline
Last seen: 2 hours 11 min ago
Joined: 03/19/2012 - 23:54
Posts: 949
Location: SoCal

Gorgeous!
Not being too handy myself- I would love to own a hand made CRX creation someday Smile

—

A well regulated Militia, being necessary to the security of a free State, the

right of the people to keep and bear Arms, shall not be infringed.

Top
Wed, 10/10/2018 - 20:06
Cereal_killer
Cereal_killer's picture
Offline
Last seen: 4 days 19 hours ago
Joined: 07/22/2013 - 13:10
Posts: 3976
Location: Ohio

How do you thread parts by hand? Especially the female side (I’ve hand cut male threads before with diamond files but no idea how you could do the female side by hand).

—

 RIP  SPC Joey Riley, KIA 11/24/14. Now I am become death, the destroyer of worlds.

Top
Wed, 10/10/2018 - 20:15
CRX
CRX's picture
Offline
Last seen: 3 hours 34 min ago
Joined: 04/02/2013 - 15:27
Posts: 3912
Location: Scotland

travis wrote:
Gorgeous!
Not being too handy myself- I would love to own a hand made CRX creation someday Smile

Thanks Wink Thumbs Up
Cereal_killer wrote:
How do you thread parts by hand? Especially the female side (I’ve hand cut male threads before with diamond files but no idea how you could do the female side by hand).

I don’t, yet. I have been looking at tap & die sets though.
I’m just a scavenger, those threaded parts are from one of those cheap laser pointers Wink

—

- LEDs & Other Stuff - - UI CheatSheets - - CRX Mods & Builds - - Stuff for Sale -  - The Old Lumens Flashlight Modders & Builders Challenge is Now Open - Link -

Top
Wed, 10/10/2018 - 20:18
MtnDon
MtnDon's picture
Offline
Last seen: 3 hours 57 min ago
Joined: 08/27/2015 - 18:25
Posts: 2561
Location: Canuk in NM

Very nice. !!!!! Thumbs Up

—

BLF Member Map Add your name and location.

Top
Wed, 10/10/2018 - 21:16
CRX
CRX's picture
Offline
Last seen: 3 hours 34 min ago
Joined: 04/02/2013 - 15:27
Posts: 3912
Location: Scotland
Beer
—

- LEDs & Other Stuff - - UI CheatSheets - - CRX Mods & Builds - - Stuff for Sale -  - The Old Lumens Flashlight Modders & Builders Challenge is Now Open - Link -

Top