Was thinking of building a few of these drivers for myself to play with. I do microsoldering so, should be easy to assemble. Wondering if anyone here would like to get their hands on one of these assembled and flashed drivers, the more I make the cheaper it is. Not looking to make a profit but just pay for parts n shipping.
GXB172 REV A2
https://oshpark.com/shared_projects/AKnfvDHZ
EDIT
-Initial order limit going to be 2 drivers. Trying to get these drivers to as many different people as I can. If I can handle it I will try to fur-fill all orders.
-Okeyed by Lone Oceans, This is a prototype driver! No warranties for issues outside of assembly of the driver.
-For now, no custom firmware. I will go through the current firmware and see if I can make any improvements or tweaks.
2/12
-Will place order for parts + pcb once paycheck comes in! (~15th). If anyone wants to pitch early or contribute anyway send a pm!
2/13
-OSHpark pcb order placed (51x) also some tail switch boards to play with!
5/2
- Parts order placed should be getting these boards assembled once parts come in (project placed on hold as job was getting busy)
I’m in for 2!
Cool that was fast! I was thinking of making between 10-50 just trying to get a feel for how many people want one of these. Mouser lead times for parts are redic 15 weeks. I will confirm in this thread if this ever happens.
Nice work autonomousperson. Would you be programming these as well?
djozz quotes, "it came with chinese lettering that is chinese to me".
"My man mousehole needs one too"
old4570 said "I'm not an expert , so don't suffer from any such technical restrictions".
Old-Lumens. Highly admired and cherished member of Budget Light Forum. 11.5.2011 - 20.12.16. RIP.
I’m in for 4…
Yes, I have a pickit3 from just like my other hobbies but if that doesn’t work i’ll just buy a ATtiny programmer. If I have the time, ill try to tinker with schematic/pcb and firmware to support 2s. Once again, Im just trying to get an idea if this project will be worth my time/has enough interest.
I have yet to contribute anything to this project yet, just possible development and manufacturing
How much will one of these cost?
Cost goes down as I make more. I didnt want to make one or two just for myself cuz it wouldnt be worth it. Im guessing around 15-35 (depends on quantity once again). In a few days i’ll give an exact figure once I get a better idea of how many I might be making. Ive shot loneoceans an email just to make sure he is okay with me doing this and waiting on a reply, the license he has on everything is Non-Commercial CC.
As you said before, since you aren’t planning to make a profit, it should be non-commercial.
You are just trying to provide a service to other people who can’t do this kind of stuff alone.
My very own high current Beryllium Copper springs Gen 3:
http://budgetlightforum.com/node/67401
Liitokala Aliexpress Stores Battery Fraud: http://budgetlightforum.com/node/60547
In for 2 and thanks.
What are the dimensions of the driver, 17mm by how tall? What firmware can you flash on it? Narsil or Anduril by any chance?
Price is good, I’m in for two.
If you get buried with orders I’d be willing to just buy the parts off of you, I want to convert one to 12 volt one anyway.
I don’t think Lone Oceans will mind if you make them, he seemed willing to get a build house to make a batch. It’s good you emailed him, if he sees there is interest in his driver he might get around to finishing the programming and release the code.
I would be in for 2 fully built and 2 part packages..if that could be an option..
KB1428 “Live Life WOT”
This driver uses a different Attiny and is programmed in Arduino, it also uses components not supported by either one of those programs. The code has not been released, just the hex so it can’t be modified in any way.
There is no schematic so it is hard to say if an adapter board can be made to put an 85 in there. Toykeeper has started porting Anduril to different Attiny’s but I don’t know how far along she is or where it is on her priority list.
The good inductor is 7mm tall, a less efficient one that will work is 3mm tall.
I’m interested in one or two depending on price
Interested in 2 as well. Been wanting to build a C8 with an XHP50 for a while
Was planning on ordering the taller inductor. I might order a few 3mm inductors and mess with the switching frequency to minimize issues (gonna have to look more into boost converter design). The large 7mm inductor is almost as expensive as the MS2429!
I would be in for 1!
http://budgetlightforum.com/node/54900?page=1
The schematic in post 54 is likely similar to this driver.
Texas Instruments has some online simulators for their controllers. Its interesting to play with inductor values, output currents and voltages. Then run the simulation and check for component, switching frequency and efficiency changes.
I think Lone Oceans gave Texas Ace a driver to test out. Maybe PM him to see if he found anything that needed tweaking.
In for 1 driver.
Courui D01 -Mod ZY-T08 Small Sun -Mod Shadow JM30 Mod - copper edition Brinyte 158B mod - copper brass hybrid
Small sun ZY-T08 Mod II - The Next Generation Small Sun ZY-T08 Best Of Both Worlds Warsun X50 mod - a complete makeover
Maglite 3C Mod - old school style
I’m not in this time but thanks a lot for doing it!
12v operation is updated on Loneoceans GXB172 REV.A2 BOM. Only two changes to make if you use 25v output capacitors.. Sense resistor (R1) and (R13). I’m using a XHP35.2 but I haven’t had a chance to do much testing yet.
V11R and V10R Current Mod
Autonomousperson can we see some of your other work? Other high (and small) parts count boards you’ve assembled?
RIP SPC Joey Riley, KIA 11/24/14. Now I am become death, the destroyer of worlds.
This is my first community project so it will be challenging however I do not expect issues assembling the board. Tomorrow @ work if i’m not too busy i’ll try to get a video of my rework skills. I have multiple irons as well as a reflow station. frequently reflow 01005 sized smd componets as well as BGA packages and will demo both. My assumption is if I can work on iPhone logic boards I can easily work on these drivers with larger sized components.
Here is something for now… https://www.reddit.com/r/mobilerepair/comments/8wnc3o/battlestationssss/
Edit
I am purchasing these parts out of my own pocket, you pay only after its assembled. No risk to you, just want more people to get their hands on this board.
As I understand, this version not support e-switch ?
If so I am interested in 2 but if price is <20$
I’d be interested in a few depending on price and firmware.
Interested in at least 1 or 2 divers. But living in Germany will probably make it very expensive (shipping + driver + customs fees).
It will depend on the final price.
New WildTrail (former LuckySun) D80v2 Sale has Started http://budgetlightforum.com/node/66255
i also have an interest in 2, i have a copper s2+ and a stainless/copper x6 on the way that are begging to have xhp50s in them
Same for me, though there might not be customs fees, it’s free up to just under 25$ in the Netherlands, i’d think it’s the same for you?
@Eleziel
Yes ~same here. Tax free threshold official 22€ (but they do not collect taxes below 5€) so inofficial the threshold is 26,30€. But the shipping costs are included in the 26,30€. And because shipping from the US is not cheap its hard to stay below this.
One option is to mark the package as a gift (tax free threshold incl shipping 45€).
But lets wait and see what the final price is. For sure a interesting driver that will open up new modding possibilities!
New WildTrail (former LuckySun) D80v2 Sale has Started http://budgetlightforum.com/node/66255
In for 2 as long as I can afford, best if one could be 12V.
[WTS] HID host: http://budgetlightforum.com/node/68693
[WTB] Interesting LEDs:http://budgetlightforum.com/node/68968
Pages