Emisar D1 / D1S review

I have the D1 xpl hi V3 1A set at 70 degrees c and showing 29 degree pcb indicated temp for both tests.[ambient 22 c]

I tested the VTC6 versus the GA

The VTC6 at start 1182

at 30 secs 1108

at 1 minute 1075 lumens

The ncr 18650 GA at start 1107

at 30 secs 1074

at 1 minute 1021 lumens.

As you can see there is a little difference in output. I personally like the sony the best as it can run most of my lights and the difference in capacity is very little between the two.

Differences of 100 lumens at this values are not perceptible.

Thanks for the info. So the GAs are only –3.1% to –6.3% less.

Any info when will be D1S available on intl-outdoor? And something else colors in the future?

Almost any decent cell should be fine in the D1 and D1S. Output on turbo may differ by small amounts, but usually not enough to be perceptible. They shouldn’t have any significant issues putting out that much current.

The D4 is another story. It tries to draw enough power to damage lesser cells. Usually the thermal regulation will reduce the output before anything bad can happen, but you could still run into issues with a first-batch model before regulation was added, or in really weird situations like if you held the button in momentary mode at turbo while wearing a heatproof glove.

In either case, good cells are certainly recommended, but it’s not as important with the D1 and D1S.

Here it is :+1:

http://intl-outdoor.com/emisar-d1s-thrower-p-926.html

$40… What a bargain… :smiley:

I’ll be ordering one when Richard from Mountain Electronics get’s them in. BTW, my Cyan D4 is being delivered today :slight_smile:

How much would a domed emitter change the beam profile of the D1?

Larger more defined hot spot, somewhat less spill.

My Emisar D1S arrived in the US today, just 12 days after ordering it via Neal’s Deals on M4D M4X’s site.

In short, I love it! :heart_eyes: Here’s a family photo with a D4 and D1.

I prefer the smooth finish of the earlier Emisars, but the new matte finish isn’t unattractive or unpleasant to handle.

I opened it immediately to swap in ToyKeeper’s awesome Andúril UI. The D1S is my 8th light running Andúril. :partying_face:

The driver fits tightly, but is not glued. I desoldered the emitter’s wires and pushed the driver out from that side.

The switch PCB’s wires are long enough to access the driver without issue.

Here’s a hotspot comparison of the D1 and D1S at 6 feet (1.83 meters) from a wall. Both are 5000K XP-L HI V2 3A.

I hope to share some outdoor beamshots comparing the D1S to a few other lights soon.

Sweet! Hoping to see mine by tomorrow.

I’ve been really disappointed with the new Emisar finish so far, aside from feeling cheap and unpleasant to me, it flakes off too easily. I have a D1 with the original finish and it is flawless despite much harder use.

Thanks for the beamshot comparison, looks pretty promising.

Did you receive any shipping or communication about it being shipped?

I have no problem waiting :innocent: Just knowing something is eventually coming would be nice :laughing:

goshdogit, that’s a really good beamshot / hotspot comparison. The PCB pic also reminds me I still haven’t taken mine apart to get pics and reflash it…

I didn’t get a shipping notice or tracking number, just an order confirmation email. I didn’t notice that at the end of the message, it instructed to reply back with my phone number.

Neal sent me another email a few days later asking again for my phone number, but I didn’t see it for several days because it went to my spam folder.

The D1S got here only 7 days after I replied to the second message with my phone number, so I wonder if Neal sent the light before I replied. Oddly, there are no dates on either of the shipping labels.

Cool, thanks. Just wondering, first time ordering anything through m4d m4x/Neal. Will order more things in the future.

I also received and replied back to the same phone number email.

When I first shined the D1 and D1S at a wall, for a moment I thought I had picked up the D4!

Whaaat?! :smiley:

When I placed my order it gave a date of when it would arrive. I let it go 4 days past (I live in Alaska and somehow it takes a week longer to get priority air mail….) before contacting Neil.

He pulled a tracking number for me and it was here shortly after that.

I did not have any dates on my package either.

give him an email and see what he says and see if he will send a tracking number. I know all orders going forward for me I will pay to have tracking number so I can watch it fly around.

fixed for you.

I’ll include my D1S tracking info so you don’t feel left out. “Send to Chicago 11/08”

Number: LSxxCN
Package Status: In Transit
Destination Country: United States
2017-11-07 02:05 Origin Post is Preparing Shipment, We have received notice that the originating post is preparing to dispatch this mail piece.
2017-11-07 02:05 CHINA, GUANGZHOU EMS, Processed Through Facility
Origin Country: China
2017-11-08 22:42 Guangzhou, leave Guangzhou sent to Guangzhou Express Company
2017-11-08 22:42 Guangzhou, leave Guangzhou and send to Chicago.
2017-11-06 18:42 Guangzhou, Guangzhou Postal Courier logistics Company International Business Branch has received (name of the Collector: Jianbo, Tel: 18818911168)

Powered by www.17track.net

Mine arrived from China today!