Buoyen
(Buoyen)
August 30, 2018, 6:29pm
610
The LD-B4HV. Can someone tell me what the different connection points in this image are: Capture hosted at ImgBB — ImgBB
+ battery power is on the back side
battery power is on the edge (I)
A is + LED, B is - LED and C is gate?
This driver should turn on when connected to power (without switch) ?
contactcr
(contactcr)
August 30, 2018, 6:45pm
611
The last page of this PDF has what you need:
Buoyen
(Buoyen)
August 30, 2018, 6:52pm
612
Ok, wasn’t sure since that is not exactly the same driver.
But then I guess my A is A in the datasheet (LED +). My B is S in the datasheet (LED - ). My C is G in the datasheet (gate) like I thought.
Thank you!
contactcr
(contactcr)
August 30, 2018, 6:56pm
613
Buoyen:
Ok, wasn’t sure since that is not exactly the same driver.
But then I guess my A is A in the datasheet (LED +). My B is S in the datasheet (LED - ). My C is G in the datasheet (gate) like I thought.
Thank you!
I glanced at your picture but there are indeed a few differences mentioned on the product page as well. Maybe it’s best to wait for LED4Power to confirm.
led4power
(led4power)
August 31, 2018, 6:12am
614
Buoyen, I sent you answer over email.
Hi Neven, can you already estimate when the new e-switch driver for Convoy C8F 21700 will be ready for sale?
Best regards, Thomas
led4power
(led4power)
September 1, 2018, 9:09am
617
Hm, I didn't mention any e-switch driver for C8F? Do you mean subZero FET switch for C8 (which uses e-switch)?
The_Driver1
(The_Driver)
September 1, 2018, 10:01am
618
When will the following things be available:
- 30A driver
- Luxeon MZ LEDs on PCB
led4power
(led4power)
September 1, 2018, 5:00pm
619
MZ leds - next week 100%
-18,24,30Amp drivers, FET switch,spacers - next week 95%
F.i.l.a.s
(F.i.l.a.s)
September 1, 2018, 5:04pm
620
What driver do you recommend for C8, 1x Luxeon MZ, Fet switch?
led4power
(led4power)
September 1, 2018, 5:11pm
621
Depends on what you want, max. output light, or light for general use, so max. current can be anywhere from 3Amp to 15Amps. 12Amps looks like sweet spot for hot rods.
led4power
(led4power)
September 1, 2018, 7:55pm
622
C8TT head build with CUTE-4-SS optics,4x Luxeon V 4000K, 24Amp LD-B4 driver and subZero FET switch:
https://budgetlightforum.com/t/-/37376/5756
Sorry if I mixed something up here. I assumed there is a LD4 driver planned with e-switch firmware on it to work with the C8F.
I asked some months ago here: https://budgetlightforum.com/t/-/46929/418
led4power
(led4power)
September 2, 2018, 2:56pm
624
I remember someone asked, well good news is that I will finally start with driver design upgrade and new firmware .This will take some time,but I think it will be worthy.
Thank you Neven! That's good news indeed. :)
Cheers, Thomas
led4power
(led4power)
September 6, 2018, 6:47pm
626
Luxeon MZ 5700K 90CRI (9080 Nichia rating) are finally here, flux bin is R!
Maukka tested MZ LED from Mouser before, it seems Mouser's reel is either high P bin,or low Q bin.
Agro
(Agro)
September 6, 2018, 6:51pm
627
1 bin up from the koef3 test. :+1:
djozz
(djozz)
September 6, 2018, 8:25pm
628
With the MZ available, I guess it is time for a new Q8 version then!
contactcr
(contactcr)
September 6, 2018, 8:28pm
629
RIP djozz’s Sofirn Q8 before it even arrives.