Copper S2+ limited edition

tvizk · February 3, 2019, 1:33pm

Hell yes please! The only reason I didn’t get your copper S2+ is because of the knurling. I don’t really like how it looks, actually I don’t like it on any light to be honest, just doesn’t look good. If it’s just plain, I’d probably get a couple!

wobba · February 3, 2019, 2:38pm

subscribed

malkoff_junkie · February 3, 2019, 3:59pm

could they also work in an 18650 tube?. x 2 18350.
optosolis quad.

BlueSwordM · February 3, 2019, 4:06pm

@HCRI9080, you could just use a buck driver since Optosolis and E21As have very low VFs, especially in a quad config.

malkoff_junkie · February 3, 2019, 4:12pm

so 2 x 18350 ok?

BlueSwordM · February 3, 2019, 4:15pm

Or you could just use a single 18650 in it.
No need to use 2x18350s then

malkoff_junkie · February 3, 2019, 4:29pm

so would 2 x 18350 come into play if it was a linear driver ?

djozz · February 3, 2019, 5:51pm

Conan_the_Worrior · February 8, 2019, 1:26pm

Any chance of a copper Convoy T2 you think?

Simon_Mao · February 11, 2019, 6:10am

good suggestion

Conan_the_Worrior · February 11, 2019, 4:56pm

Welcome back Simon. Hope you enjoyed your holiday.

NOW GET BACK TO WORK ! ! !

SKV89 · February 11, 2019, 5:12pm

Simon, I really want to buy a bunch of T2 for modding but I don’t like the driver. Can you consider improving the driver to be like the one on the Reylight TiLan and Brass AA? Reylight have the best AA flashlight rear clicky UI/driver I’ve used. The Sofirn SF14 comes in second. They have no PWM.

djozz · February 11, 2019, 5:50pm

In case a completely new driver (which would happen there were to be no PWM) is not feasable, perhaps the current driver can be changed to a higher PWM frequency, anything over 5000 Hz should be a vast improvement.

And when the software for the T2 is adapted anyway, the double-click timing for strobe should be much shorter so that when clicking twice to get from low to high does not result in strobe (like what happens to everyone with the current T2).

samyy · February 11, 2019, 5:54pm

…and the 14500 support would be very nice…(…for the possible copper T2…)

DB_Custom · February 12, 2019, 7:27pm

Y’all keep forgetting how much smaller a company Convoy is, difficult for him to develop the kind of drivers you’re asking for. Sofirn is a big company by comparison, and I’m not sure exactly where Rey sourced that driver.

Perhaps it doesn’t hurt to ask, but it may be asking too much…

contactcr · February 12, 2019, 7:52pm

I thought it was common knowledge Reylight is just custom runs from lumintop? idk

DB_Custom · February 12, 2019, 7:58pm

So if I eat a Lumintop Mini GT I’ll have the custom runs?

DB_Custom · February 12, 2019, 8:00pm

Sorry, my bad, couldn’t be helped…

Simon_Mao · February 13, 2019, 4:18am

i have other AA driver without PWM several years before ,
it’s LDCH LD30

Its disadvantage is that the components are too dense, not easy to install, easy to short circuit

DB_Custom · February 13, 2019, 1:31pm

Thank you for clarifying, Simon. Nice to see you online and providing options.