hank wrote:

Streamer wrote here: http://budgetlightforum.com/comment/1412461#comment-1412461

Quote:

Convoy S2 clicky tailcap fits the [Sofirn] Sp32 perfectly and will function as a lockout

Convoy T2 head in Jaxman E3 body (I cannot test the E3 head on the T2 body has I removed the driver from it Will try it when I het the driver )

I have found that the Convoy S2+ short tube (ordered from Convoy store) does not work with the Sofirn SP32A V2.0. This was a disappointing finding since MascaratumB reported that it worked in post 113 of this thread. However I now realize that was probably the V1 version. I also tried the tail cap from the Convoy S2, as this was reported to work by Streamer in post 122 above, and it does not fit. Again he says SP32 so I am not sure which version but I think V1. So as far as I can tell something is different about the SP32A V2.0 threads. If anyone has the V2.0 version and can find a short tube that works with it I would like to know about it.

Scientist wrote:

I have found that the Convoy S2+ short tube (ordered from Convoy store) does not work with the Sofirn SP32A V2.0. This was a disappointing finding since MascaratumB reported that it worked in post 113 of this thread. However I now realize that was probably the V1 version. I also tried the tail cap from the Convoy S2, as this was reported to work by Streamer in post 122 above, and it does not fit. Again he says SP32 so I am not sure which version but I think V1. So as far as I can tell something is different about the SP32A V2.0 threads. If anyone has the V2.0 version and can find a short tube that works with it I would like to know about it.

Scientist, I am using the tube with the SP32 V2.0! The tube must be reversed, with the non anodized threads towards the tail of the Sofirn light!
Unless there was a new modification of the SP32 host (probable…) the tube will fit and work! I have one configured like that since I showed it in the picture!
Have you tried to use it reversed?

Yes I have tried both ways. The threads start but the tube does not seat deep enough. Perhaps I just have to try another tube.

antiparanoico wrote:

Astrolux SC/Ultrafire C3 SS (1st version, 93mm).

!http://i.imgur.com/TNeHnf8l.jpg!

ughly! just because you can, doesn’t mean you should!
geneticists take note!

Sofirn C01 legoes with the Maratac copper AAA

Would be nice to get the smaller ones to light up

MascaratumB wrote:

Would be nice to get the smaller ones to light up

DavidEF wrote:

MascaratumB wrote:

Would be nice to get the smaller ones to light up

Button cells? That would be cool to see.

djoozzzzz, can you try it? Just for fun

MascaratumB wrote:

DavidEF wrote:

MascaratumB wrote:

Would be nice to get the smaller ones to light up

Button cells? That would be cool to see.

Hum, would it be possible?

djoozzzzz, can you try it? Just for fun

djozz wrote:

MascaratumB wrote:

DavidEF wrote:

MascaratumB wrote:

Would be nice to get the smaller ones to light up

Button cells? That would be cool to see.

Hum, would it be possible?

djoozzzzz, can you try it? Just for fun

LOL, no chance, the driver boards are already touching each other.

MascaratumB wrote:

djozz wrote:

MascaratumB wrote:

DavidEF wrote:

MascaratumB wrote:

Would be nice to get the smaller ones to light up

Button cells? That would be cool to see.

Hum, would it be possible?

djoozzzzz, can you try it? Just for fun

LOL, no chance, the driver boards are already touching each other.

Noooo fun then

The Convoy S2 vs Convoy S2+ 18650 & 18350 tubes!
As posted on another thread, the Convoy S2 gray (bought from Simon) can be used with the black & desert tan 18650 tubes and the gray, black & desert tan 18350 tubes!

Also, the S2 gray tube can be used in the “short” Convoy S2+ (blueish gray) [no photo of that one, sorry].

djozz wrote:

Sofirn C01 legoes with the Maratac copper AAA

these all work

and these

nightshade;5274543 wrote:

for the RRT01, there is a 18650 Crelant that was a very definite body fit and also the Jetbeam TCR10 AA titanium adapter was another that was a direct fit for the RRT 01 , TCR1, Niteye. The Niteye series offered 18650, 2-AA bodies as well, that fit the RRT01.

here is 18650 Eye15 and 18350 Eye10

The Skilhunt DS20 legoes with the (shorty) battery tube of the BLF-A6. The o-rings do not engage at all so the combination is not waterproof, but it works fine on a 18350.

Sofirn SF32 legoes with Convoy S2+

BLF A6 legoes with Astroloux S41S

Sofirn C8T legoes with Convoy C8+

Jetbeam/Niteye RRT-01 to Jetbeam/Niteye TCR-1

Fire Flies E01 and E 07 are the same except for the head. All parts interchange, same tube same tailcap.

V10r Ti w AA extender from V11r

The Nitecore P12 tailcap fits perfectly onto the Nitecore P30. It makes it easier to use a lanyard without having to use the tactical ring on the P30, and it will tail stand. Tail standing is not perfect because the rubber boot on the P12 switch is a bit taller then the cap. However, It does work as you can see in the pic.

Would know if the New copper S2+ can Lego with others

Alen wrote:

Would know if the New copper S2+ can Lego with others

Nope...completely different threads than any other S2

id30209 wrote:

Alen wrote:

Would know if the New copper S2+ can Lego with others

 

Nope…completely different threads than any other S2

Am I the only one who found out that a euro coin can become pretty stuck inside a D4 bezel?

It just so happens that I'm on the bus on my way home and I also happen to carry my D4V2 and 90% sure that I should have some change in my wallet. Now.. let's see if no one is looking my way and..

Nope, just joking.. But, all of a sudden just realised.. my trip home seems to have gotten that much longer for whatever reason, I wonder why that could be, hmm..

Nitefox ES10K and Lumintop Tool AA V2.0
Functionally “legoing”