[M4D deal] FW3T Titanium Stonewashed - Interest list open

Ordered a stonewashed SST20 – thanks

The all-polished Ti looks amazing.

But I ended up ordering a Ti-Cu. I’m not sure pure Ti could handle turbo heat without desoldering itself.

If you compare these lights to an HDS/Oveready BOSS/Prometheus light/etc this is the cheapest what I would call an exotic/custom light out there!! - does pretty much what theirs do but smaller/cheaper so you can buy 4 FW3’s (in Ti) to 1 of theirs.

Pretty sure it would be 10 FW3T to 1 HDS Ti, but hardly apples to apples. Both amazing.

It couldn’t desolder itself as the electronics would throttle it back from heat way before that would happen - I thought about getting the Ti/Cu one too but in reality you will only get an extra 5 seconds maybe in boosted time before it throttles back once the Cu is saturated in heat, I just didn’t want the middle to be the weak point with all that Ti because the Cu tube is only about 1.5mm at it’s thickest the tread and 1mm where there is no thread.

Copper and brass lights are pretty, but… I work in the semiconductor industry and I like to use my lights at work. Copper is a big-time contaminant when it comes to manufacturing microprocessors. Even just touching a copper component and then touching a piece of equipment without changing gloves can cause major contamination. So, stonewashed titanium for me :smiley:

Would having the all-copper FW3C make significant difference or is the mass of the flashlight just too small?

I don’t plan on using the turbo much so maybe I can get away with an all Titanium build?

Yes the all Cu one would be the coolest running of all of them, but you would also have the softest metal of all (I personally wouldn’t want to drop it on a hard surface as it would dent/scratch easily) But I think you are right saying “the mass is just too small”
IMO the Ti one would probably be better run in the muggle mode, that way it wouldn’t overheat and still having heat protection for backup, all Ti custom lights have fairly low output compared to Alu/copper, anyway most get Ti for coolnessbulletproofnessarmagedoness :smiley:

Got a polished ti ordered. Hopefully there isn’t a wait on the polished like there is for the stonewashed. Does anyone know if the polished are shipping yet?

I put an order in for a Polished Ti on 8/7/2019 and it has not yet shipped. It’s getting pretty close to the estimated ship date for the stonewashed, which is 8/20/2019.

Oh well, for me if I need almost 3,000 lumens of illumination for a long period I wouldn’t be using my FW3A at all but some other light.

It’s simply too much requirement for this little baby.

I ordered my stonewashed FW3T on Aug 7 and no word yet. I know the target was Aug 20. Anyone have an update from Neal? (I emailed him earlier today and will report back if he provides an update).

Ordered stonewash on the 8th Aug - got notification on 27th Aug that it was posted.

Niiiice. So I might be hearing from Neal very soon!

Also ordered on August, 8 - shipped August, 27

DHL just let me know to expect mine Sept 4.

Still no update from Neal and no response to my last two emails… wtf

Got mine over a week ago, hope you guys have/are getting yours.

Got mine as expected—Sept 4. Works like a champ. Wife loves her purple SST20.

My only complaint is that her “lava” glow insert is quite dim compared to my green one—I knew it would be dimmer, but I was expecting visually 1/2 brightness or so, however, it is more like 1/10 visually.

Didn’t know where to put this question really, so here’s to waking a necrothread.

Does anyone have any idea where I could get a stonewashed TI shorty tube to go with my copper FW3? Also after an 18650 tube but have no idea if they were ever produced as spares. I’ve emailed Neal, but if anyone knows another source I’d be grateful.