How does it focus after dedoming?
Thank you mudgripz.
paypal sent, thanks Krono and Amanda.
Linh
I must have missed you jmpaul…sorry!!!
jmpaul320: MTAmanda:Invoices to magnet, MoZuKa, troisanh, gorky, bkling, have been sent through Paypal.
Make sure to leave a correct address please. With telephone number will be better. Normally parcel with tel. No. will be despatched faster….
Thank you.
can you please invoice me - my paypal is jmpaul320(at)gmail.com
I must have missed you jmpaul…sorry!!!
lol its ok
I messaged amanda but no response yet
i think its still early morning in the far east
Looks great - I seriously like my dedomed new 2X.
Here’s gadgetman’s 5 minute dedoming method:
“Basically I hold the LED board in a vice with little wooden soft jaws I made up to provide insulation. I use a hot air attachment on a gas powered soldering iron (not a gas torch) and heat the underside of the board until I see the lead flow (melt). Then I gently press down on the dome with a concave ground screwdriver and hold it for a few seconds, making sure not to move the LED. This lifts bottom of the dome around the four sides of the emitter surface as well as testing if the dome is soft enough; if not soft enough I apply a little more heat.
Once soft enough (and the solder has taken again) I lift the dome off by popping a screwdriver under the edge of the dome on the opposite side to the fine gold wires. Normally the dome will just pop off with a little pressure. If the dome does not soften enough or it is reluctant to pop off I soak in petrol. The heating and lifting of the edges speeds this process any way.
Similar to this but it pops off a lot quicker and cleaner.
[video]https://www.youtube.com/watch?v=vfC3n2jlZY4[/video] ”
MTAmanda:Invoices to magnet, MoZuKa, troisanh, gorky, bkling, have been sent through Paypal.
Make sure to leave a correct address please. With telephone number will be better. Normally parcel with tel. No. will be despatched faster.
Thank you.
can you please invoice me - my paypal is jmpaul320(at)gmail.com
Just sent
Jump on the hype train, people!
pp sent!
Looks great - I seriously like my dedomed new 2X.
Here’s gadgetman’s 5 minute dedoming method:
“Basically I hold the LED board in a vice with little wooden soft jaws I made up to provide insulation. I use a hot air attachment on a gas powered soldering iron (not a gas torch) and heat the underside of the board until I see the lead flow (melt). Then I gently press down on the dome with a concave ground screwdriver and hold it for a few seconds, making sure not to move the LED. This lifts bottom of the dome around the four sides of the emitter surface as well as testing if the dome is soft enough; if not soft enough I apply a little more heat.
Once soft enough (and the solder has taken again) I lift the dome off by popping a screwdriver under the edge of the dome on the opposite side to the fine gold wires. Normally the dome will just pop off with a little pressure. If the dome does not soften enough or it is reluctant to pop off I soak in petrol. The heating and lifting of the edges speeds this process any way.
Similar to this but it pops off a lot quicker and cleaner.
[video]https://www.youtube.com/watch?v=vfC3n2jlZY4[/video] “
Thanx again mudgripz.
Alright. Can’t stand it anymore. Put me down for one.
acumenflashlights(at)gmail.com
Muahahahaha! J)
Bad news is—- our nylon bag is just out of stock yesterday. Next production will arrive on next Wednesday.
Good news is—- Paid orders, which are not delivered this week, will upgrade to 7-day shipping for free.
The waiting is like a torture…… :bigsmile:
I would just like to say that there are no MAP issues with this or any MaxToch GB. That is all :bigsmile:
The waiting is like a torture…… :bigsmile:
Hey MoZuKa, can you pls PM your telephone number to me? The expedited shipping way requires telephone number. Await your reply.
MoZuKa:The waiting is like a torture…… :bigsmile:
Hey MoZuKa, can you pls PM your telephone number to me? The expedited shipping way requires telephone number. Await your reply.
PM send.