For Sale 502b XM-L2 De-domed 900 lumens and 502b nichia 219 extra heatsinking and sinkpads $40 shipped for both

20 posts / 0 new
Last post
18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161
For Sale 502b XM-L2 De-domed 900 lumens and 502b nichia 219 extra heatsinking and sinkpads $40 shipped for both

OK up for sale tonight. Two 502B’s $40 for both of them and that includes shipping if you are in the US. $35 plus exact shipping if you anyplace else.

Both lights are on sinkpads and as always I have used professional grade thermal grease. I have added a large copper sleeve to both mods as well for excellent heat transfer away for the reflector and pill. Both have spring mods on the positive ends. Then negative ends have the solid brass caps that also make great contact. I have used Bell Wire to replace each set of wires. Bell Wire is a single large strand of copper wire.

The XM-L2 is rocking out 900 lumens and is de-domed for amazing throw for a pocket light.

The Nichia is a high CRI with a beautiful tint and beam.

Both driver are 5 modes and have memory so when you turn them back on they will be in the same mode that you left them in. Both drivers have of course been modded to put out more amps then they did stock.

$40 free shipping US
$35 plus exact shipping for everyone else. (shouldn’t be too bad they are not that heavy even with the copper)

As usual first PM gets these.

I might do some more if anyone is interest. So if someone gets these first just ask and I can toss a couple together for you. I have the parts, it’s just a matter of putting them together. They are time consuming little mods.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

Edited by: 18sixfifty on 06/21/2014 - 02:38
likevvii
Offline
Last seen: 1 day 13 hours ago
Joined: 04/28/2014 - 10:12
Posts: 422
Location: USA, California

I think even if you have sold these, you should still post a few pics to get more hype for the next mods you sell. I am really really curious on what nifty stuff you make and sell every time!

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161
likevvii wrote:
I think even if you have sold these, you should still post a few pics to get more hype for the next mods you sell. I am really really curious on what nifty stuff you make and sell every time!

Thanks and I should take your advice. I just get busy modding and always forget to take pics. I pretty much just end up modding whatever I’m in the mood for and if it turns out nice I post it for sale. If not it goes on the shelf to get worked on another day. I’ve got about 20 projects waiting to get modded and I also end up working on some members lights too. I like using them but I love modding them even more.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod. :bigsmile:

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

travis
Offline
Last seen: 3 days 7 hours ago
Joined: 03/19/2012 - 23:54
Posts: 1010
Location: SoCal

interested in the xm-l

“"A free people ought not only be armed and disciplined, but they should have sufficient arms and ammunition to maintain a status of independence from any who might attempt to abuse them, which would include their own government.””
-George Washington

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161

Sold the XM-L2 but I’ll just make another one or two up so I’ll leave this up for now.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

strongest2004
strongest2004's picture
Offline
Last seen: 1 year 10 months ago
Joined: 01/24/2014 - 19:32
Posts: 370
Location: Philippines

Hi.
Will take both, if not yet taken.

Thanks

Low mode and long runtime lover…

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161

Sent PM

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

deckart
deckart's picture
Offline
Last seen: 7 years 2 weeks ago
Joined: 06/05/2014 - 14:04
Posts: 88

Is the nichia de domed ?
What amps at tailcap ?

Rufusbduck
Rufusbduck's picture
Offline
Last seen: 7 months 1 week ago
Joined: 04/04/2012 - 15:34
Posts: 10389
Location: Golden state

I too am curious to see a pic of your heat sinking. I just add a split piece of 3/4” copper pipe around the p60 module but always happy to borrow a better idea. Smile I recently purchased a 20mm tap and die to see if I could make an all copper version but haven’t had the time to try it yet. I’m shameless about combining my ideas with others’ and am always on the prowl. 0:)

Three Tanna leaves to give him life, nine to give him movement. But what if he eats the whole bag?

Scott

Hi-Beam
Hi-Beam's picture
Offline
Last seen: 6 years 1 month ago
Joined: 06/01/2014 - 22:37
Posts: 248
Location: TX

18sixfifty wrote:

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod. :bigsmile:

Hugh, say that again, I’m confused, who’s on first? what’s on second…
18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161
deckart wrote:
Is the nichia de domed ? What amps at tailcap ?

No the nichia isn’t de-domed and I don’t really take tailcap readings they are all over the place really don’t say all that much. They are both driven very hard for this size light.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161
Rufusbduck wrote:
I too am curious to see a pic of your heat sinking. I just add a split piece of 3/4” copper pipe around the p60 module but always happy to borrow a better idea. Smile I recently purchased a 20mm tap and die to see if I could make an all copper version but haven’t had the time to try it yet. I’m shameless about combining my ideas with others’ and am always on the prowl. 0:)

Slit piece of copper is what I’m using now too. Although I would also add potting material to that and fill it in completely if I thought that people would be happy no longer being able to use it as a drop in.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

MRsDNF
MRsDNF's picture
Offline
Last seen: 3 months 2 weeks ago
Joined: 12/22/2011 - 21:18
Posts: 13473
Location: A light beam away from the missus in the land of Aus.

Rufusbduck wrote:
I too am curious to see a pic of your heat sinking. I just add a split piece of 3/4" copper pipe around the p60 module but always happy to borrow a better idea. Smile I recently purchased a 20mm tap and die to see if I could make an all copper version but haven't had the time to try it yet. I'm shameless about combining my ideas with others' and am always on the prowl. 0:)

Did you get the tap and die locally or elsewhere?

 

djozz quotes, "it came with chinese lettering that is chinese to me".

                      "My man mousehole needs one too"

old4570 said "I'm not an expert , so don't suffer from any such technical restrictions".

Old-Lumens. Highly admired and cherished member of Budget Light Forum. 11.5.2011 - 20.12.16. RIP.

 

saypat
saypat's picture
Offline
Last seen: 20 hours 59 min ago
Joined: 07/13/2011 - 20:32
Posts: 3580
Location: Calif

So, $40 shipped for (2). Does that then mean $20 for (1) shipped?

I wish I had as much fun as you appear to have!

Rufusbduck
Rufusbduck's picture
Offline
Last seen: 7 months 1 week ago
Joined: 04/04/2012 - 15:34
Posts: 10389
Location: Golden state

MRsDNF wrote:

Rufusbduck wrote:
I too am curious to see a pic of your heat sinking. I just add a split piece of 3/4” copper pipe around the p60 module but always happy to borrow a better idea. Smile I recently purchased a 20mm tap and die to see if I could make an all copper version but haven’t had the time to try it yet. I’m shameless about combining my ideas with others’ and am always on the prowl. 0:)

Did you get the tap and die locally or elsewhere?


Tap was at the local junkyard and the die was online. ~ $10 each. I think it’s the right size for p60 threads. 20×1mm.

Three Tanna leaves to give him life, nine to give him movement. But what if he eats the whole bag?

Scott

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161

saypat wrote:
So, $40 shipped for (2). Does that then mean $20 for (1) shipped?

I wish I had as much fun as you appear to have!

Howdy, I could do $24 for one. I still get stuck shipping them and either way it costs about the same.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

strongest2004
strongest2004's picture
Offline
Last seen: 1 year 10 months ago
Joined: 01/24/2014 - 19:32
Posts: 370
Location: Philippines

Payment sent via PP 18sixfifty.
Excited to have them soon!

Best!

Low mode and long runtime lover…

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161

strongest2004 wrote:
Payment sent via PP 18sixfifty.
Excited to have them soon!

Best!

Got the payment and I’ll get them out on Monday.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.

jealous57
Offline
Last seen: 2 months 3 weeks ago
Joined: 04/17/2014 - 22:29
Posts: 700
Location: Upstate NY, USA

If you make any more of these, I may be in for a set Smile

18sixfifty
18sixfifty's picture
Offline
Last seen: 2 years 1 month ago
Joined: 12/25/2012 - 20:19
Posts: 4161
jealous57 wrote:
If you make any more of these, I may be in for a set Smile

Just let me know I have the parts ready to make more.

I’m a junky, I mod lights so I can sell lights so I can buy more light to mod so I can sell lights to buy more lights to mod.