Hello World

Flashy_Mike · 2018-10-25T06:40:43.000Z

Andrew_Debbie:

My firmware development environment is coming together.

Nice! But you shouldn’t need the extra power supply - the USBASP serves pretty well as power supply alone.

chadvone · 2018-10-25T13:18:05.000Z

I found a driver and made contact last night.
I am planning on just using a driver to test on.

What are disadvantages of doing it this way?

Andrew_Debbie · 2018-10-25T13:48:17.000Z

The biggest one is you are stuck with that driver’s hardware configuration. That doesn’t matter if you are targeting that driver anyway.

chadvone · 2018-10-25T13:54:27.000Z

Andrew_Debbie:

The biggest one is you are stuck with that driver’s hardware configuration. That doesn’t matter if you are targeting that driver anyway.

Great. I still like your set up but would like to keep it cheap. Might mount driver and led on small board with switch so it dont get knocked around.

Andrew_Debbie · 2018-10-25T14:04:35.000Z

Flashy Mike:

Andrew_Debbie:

My firmware development environment is coming together.

Nice! But you shouldn’t need the extra power supply - the USBASP serves pretty well as power supply alone.

Yes. My bargain breadboard came with a power supply. There is another 3-pin regulator on the digispark board. In case I don’t already look like a total idiot, the digispark is self programming. Will erasing the Arduino bootloader make me even more of an idiot? I’m not sure if that is possible.

Andrew_Debbie · 2018-10-25T14:22:13.000Z

chadvone:

Great. I still like your set up but would like to keep it cheap.

USBASP — $2.30
Ribbon Cable $1.64
Digispark $2.01
Breadboard, jumpers and power supply £4.63

Total is just under $12 US.

A name brand SOIC clip is going to blow the entire budget.

A 3M SOIC 8 clip is about £20 from a trusted UK supplier. The Pomona 5250 is £12.98 from Farnell.

I could get one from AliExpress for a fraction of that but that might be a mistake. Need to research.

chadvone · 2018-10-25T15:32:20.000Z

I did spring for the good clip. The one I got 2 winters ago gave me head ache.
I have a lot to learn about programming

Andrew_Debbie · 2018-10-25T15:47:52.000Z

Well that was easy….

PWM could be entirely wrong but I don’t care. This was just to test compile and flash.

~/AVR/HelloWorld$ make
CC STAR_smaller.o
avr-gcc -Wall -g -Os -mmcu=attiny85 -o STAR_smaller.o -c STAR_smaller.c
LD STAR_smaller.elf
avr-gcc -Wall -g -Os -mmcu=attiny85 -o STAR_smaller.elf STAR_smaller.o
OBJCOPY STAR_smaller.hex
avr-objcopy -O ihex STAR_smaller.elf STAR_smaller.hex
SIZE STAR_smaller.hex
avr-size STAR_smaller.hex
text data bss dec hex filename
0 892 0 892 37c STAR_smaller.hex

~/AVR/HelloWorld$ make flash
FLASH STAR_smaller.hex
avrdude -c usbasp -p t85 -u -Uflash:w:STAR_smaller.hex -Ulfuse:w:0xe2:m -Uhfuse:w:0xdf:m -U efuse:w:0xff:m

…
avrdude done. Thank you.

chadvone · 2018-10-25T15:47:10.000Z

Great. Looks confusing to me. Will be trying it soon

Flashy_Mike · 2018-10-25T16:04:58.000Z

Andrew_Debbie:

Yes. My bargain breadboard came with a power supply. There is another 3-pin regulator on the digispark board. In case I don’t already look like a total idiot, the digispark is self programming. Will erasing the Arduino bootloader make me even more of an idiot? I’m not sure if that is possible.

Well, the boot loader is gone anyway now, I guess. In case you want to build more test devices or brick your digispark, you could simply order cheap Attiny85 in DIL housing, just search vor “ATTINY85-20PU”.

Congratulations for your first flashing!

Tom_Tom · 2018-10-25T16:33:54.000Z

Well, you could try to programme something decent in the Arduino environment, but I don’t think anyone has tried here.

I agree, I suspect the bootloader is now gone. Putting one back could be a challenge, and it takes up a LOT of space.

So, maybe time to learn how things really work and buy a few bare devices. They are not expensive and readily obtainable in the UK.

Andrew_Debbie · 2018-10-26T07:12:32.000Z

The digispark was only $2.01 including shipping. RS sell the ATTiny85-20PU in packs of 5 at £1.066 each.

Flashy_Mike · 2018-10-26T08:59:44.000Z

Not much of a difference indeed.
Where did you buy the digispark? Might find a use for it one day.

Andrew_Debbie · 2018-10-26T10:05:05.000Z

Fasttech.

They sell the populated board in two versions.

$1.88. or $1.59 for 5.
https://www.fasttech.com/products/0/10042079/9067100-digispark-kickstarter-usb-development-board

$2.01 This is the one I have.
https://www.fasttech.com/products/0/10023370/5054500-usb-interface-digispark-kickstarter-attiny85

The $1.88 version doesn’t have the 3pin header. I may buy some of them for other projects.

Andrew_Debbie · 2018-10-26T10:57:35.000Z

chadvone:

Great. Looks confusing to me. Will be trying it soon

If you’ve never done this before, there is a fair amount to learn. It isn’t hard.

I made a few small edits to the makefile and STAR_smaller.C to target an ATTiny85. Next, I ran make. I pasted some of the output back here to show that it worked.

I can walk you through the edits if that would help.

What I flashed to the ’85 may not work. I don’t care since I was testing compile and flash.

Tom_Tom · 2018-10-26T15:34:39.000Z

Andrew_Debbie:

The digispark was only $2.01 including shipping. RS sell the ATTiny85-20PU in packs of 5 at £1.066 each.

It’s not a Digispark, from Digistump, which would cost about $8. If they had stock, which seems increasingly unlikely given that this unfair “competition” AKA blatant cloning, carries on.

Just a knock-off.

Drive to the bottom, then be surprised when the true innovators have to give up.

Whether that troubles you is another matter. Meanwhile you may still be able to download binaries and source from Digistump to use on this.

Andrew_Debbie · 2018-10-26T20:35:49.000Z

Not really. The digispark design is open source under CC-BY-SA 3.0 I suppose they shouldn’t be calling it a Digispark. But would it really matter if it was a Digisparc or DoggieSpark?

(emphasis mine)

You are free to:

Share — copy and redistribute the material in any medium or format
Adapt — remix, transform, and build upon the material
for any purpose, even commercially.

Looks like Digistump are doing fine.
http://digistump.com/products/1

We are also temporarily sold out of Digisparks (over 50k sold!). We will return to normal operations and restock in October 2018.

chadvone · 2018-10-27T05:10:16.000Z

Andrew_Debbie:

chadvone:

Great. Looks confusing to me. Will be trying it soon

If you’ve never done this before, there is a fair amount to learn. It isn’t hard.

I made a few small edits to the makefile and STAR_smaller.C to target an ATTiny85. Next, I ran make. I pasted some of the output back here to show that it worked.

I can walk you through the edits if that would help.

What I flashed to the ’85 may not work. I don’t care since I was testing compile and flash.

Thank you, Yes I am sure I will need some help. I am not to that point yet.
I am happy at this point to make contact with the Atiny 13 on a scrap driver. I will soon get set up with a better driver, switch and led to test on.

chadvone · 2018-10-29T05:10:13.000Z

I flashed my D4 with Anduril. But broke off a resistor and then the switch wire.

Just used the Hex file, didn’t do any thing special.

chadvone · 2018-12-19T17:22:28.000Z

I downloaded simple momentary UI just to see if I could flash it to driver from the code.

When I avr-gcc. I get errors on the uint8_t (and16t) compiler suggest unint128_t.