knife lube?

sbslider · 2019-06-16T13:42:32.000Z

great, thanks for the ideas!

I have some tri-flow from using on my bicycle, that worked great.

TrueRMS · 2019-06-16T16:54:23.000Z

On knives that will touch food I use mineral oil. 100% good safe.

Do note our beloved super lube makes an USDA approved food safe oil too that you can usually find at restaurant suppliers, if you don’t like mineral oil.

lampliter · 2019-06-16T16:58:45.000Z

Ballistol. multi-purpose.

Cosmodragoon · 2019-06-23T22:46:16.000Z

I prefer non-toxic lubes on my EDC gear. On knives and multi-tools, I tend to wipe down metal surfaces with mineral oil. For pivots, detents, etc., I use Lubriplate FMO 350-AW. I originally started using it on revolvers after reading an article by Grant Cunningham. A couple years ago, I tried it on a knife pivot and I haven’t used anything else since. It’s been great.

Here is that article. While written for the gun community, a lot of this applies to the knife and gear community overall. It’s worth a read.

https://www.grantcunningham.com/2006/05/lubrication-101

When the article was written, it was more difficult to find this oil in reasonable container sizes. A company called “Lubrikit” solved that problem for me.

http://lubrikit.com/?gclid=EAIaIQobChMIqouPq9SA4wIVkVENCh3BFgRBEAAYASAAEgLLdPD_BwE

The torsion bar in Kershaw SpeedSafe knives requires grease. The non-toxic grease used by Lubrikit is a little thin for that application. A Kershaw employee turned me on to “White Lightning Crystal Grease”. I’ve only been using it a short while but so far, it’s been great.

copperheaded · 2019-06-23T22:56:08.000Z

Nano Oil

dragunbayne · 2019-07-21T17:30:58.000Z

Does anyone use Tuff-Glide? I’ve seen it recommended on knife forums.

Dougiestyle · 2019-07-21T23:55:53.000Z

A buddy works for an airline service hub, and he hooked me up with Moly-K. Similar to graphite, except slipperier(?). I use a syringe to dispense tiny amounts. Super black stuff, though.

Macka17 · 2019-07-22T00:15:28.000Z

“”I have some tri-flow from using on my bicycle, that worked great. Thumbs Up””

Great stuff I’ve used for yrs.

But. For chains.
Std lub will throw off. especially if you do distance work.
Buy the correct. “STICKY”chain oils It stays on.
and chains last longer. less resistance.
I’m still using up the last can of my Motorbike chain lube
I used on drive chain on Yacht anchor winch (Home made)

deleted-200707 · 2019-07-22T00:18:20.000Z

I have always used Militec-1 on my guns, knives, fishing gear, flashlights.
Between 100°F and 150°F heat after application causes actual bonding to the metal and results in a dry lubricious surface which does not attract/hold dust.

http://www.militec1.com/index.html

matik42 · 2019-07-22T04:58:40.000Z

dragunbayne:

Does anyone use Tuff-Glide? I’ve seen it recommended on knife forums.

If I correctly remember it not food safe

toddcshoe · 2019-07-22T07:13:25.000Z

I have always used Hoppes #9 or Rem Oil. NOT FOOD SAFE. Don’t drink it.

Petr_Sixta · 2019-07-22T07:22:40.000Z

I use Ballistol.
It is approved for food processing machines.
I also use the knife for food

strayz · 2019-07-22T21:53:01.000Z

Frog lube. No squeaky frogs around here.

roughrider · 2020-04-24T02:20:18.000Z

I’ve had good luck with this on locks, hinges, and knives. A couple bucks and you can get it at Wal-Mart & Lowes.

cloggy · 2020-04-24T06:04:45.000Z

+1 for Ballistol.
One thing I found out about Ballistol is that it reacts to brass so if you decant it into an oil can the can should not have brass innards.
Presumably also applies to brass flashlights.

Theodore41 · 2020-04-24T08:08:45.000Z

Having enough expensive Japanese kitchen knives,the best protective oil for them is KUROBARA 100% Pure Tsubaki Japanese Knife Maintenance Camellia Oil (8.6 oz) from Amazon.

will34 · 2020-04-24T08:22:44.000Z

I use a $3 8oz bottle of mineral oil for my knives and it works great. Doesn’t seem to attract gunk as some of the “gun oil” I tried, but it is pretty thick. I ordered a KPL to try it out, it is supposed to be even lighter than nano oil 10 weight. Should work better on the free fall shut knives.

tu_army · 2020-04-24T10:33:47.000Z

i use small victorinox knife oil.

Johann · 2020-04-24T12:16:11.000Z

TRIFLOW as a wet lube.

BoeShild T-9 a most excellent dry lube developed by Boeing Aircraft.
Check reviews if interested.

Saved the Lubri-Kit link, thanks.

Macka17 · 2020-04-24T15:38:17.000Z

Torch threads. I’ve always used INOX NSF Prem Machinery Grease. With PTFE.
High Temp. Food grade. EP.

Keeps threads real nice. NOT messy and slick.