Low/lowish/Moonlight one mode only driver for P60 module

Hi everybody !

I’m relatively new here, have been a long time lurker but I’m only starting to post :wink: First of all I’d like to apologize for my English, since it is not my native language…I’ll try my best !

To be short, I’m looking for a really low output driver (like 5mA or so), to power a single mode “moonlight only” P60 module.

I know it can be considered as a waste of a good led, or a not useful at all P60 module, but after looking for the perfect bedlight (for me, as my night vision is not that good and is easily ruined), and trying a lot of multimode with moonlight P60 modules or lights, I was always disappointed, maybe except by the Thrunite archer 1A (which features a forward clicky and changes mode only by twisting the head), and I haven’t found anything that will suit my needs (I’m looking for momentary, and no mode switching if I push the switch several times by inadvertence or sleepiness).

To get into the details, I’d like to use a Solarforce P60 host (probably a L2m or L2p), with this remote switchpad : solarforceflashlight-sales.com - Informationen zum Thema solarforceflashlight sales.

it offers momentary only via switchpad, and a classic forward clicky at the tailcap, perfect for me :heart_eyes:

Now regarding the output part…I’m looking for a really low output, to read my alarm clock or bathroom/kitchen trips. After playing a bit with different emitters, I’ve found that a ~5mA driver output and a warm white emitter would be perfect for me. I’ve tried a Qlite driver and a MC-E warm emitter, and the moonlight mode is perfect, but I tend to switch to higher modes too easily :frowning:

So now I have (at least) two way to do it ; the “complicated” way with a Nanjg driver programmed into a single mode low output only (don’t know if it’s feasible, I’m only starting to look into driver programming, and I haven’t been successful at all for the moment), or an easy/archaic way, with just a resistor or something like that (LM317 voltage regulator ?).

The problem is, in both cases, I don’t know how to do it (except with resistor maybe, but the output will be very dependent on the battery voltage no ?). Is there a driver that can be modded easily to fit my needs, or should I just try to put a resistor in a not so direct drive module ? Maybe I should just use a 3mm or 5mm low power led with a resistor (but the beam profile will be mode difficult to tweak in a P60 reflector) ?

In any case, I’ll be more than happy to have your opinion on the subject :slight_smile:
Thank you for reading me, and happy new year everybody !

Hi,

ask DRJONES!

http://drjones.dyndns.info/

The Lupodrv should fit your need. Number of Modes (1-5) and brightness (16 Steps - Ultralow-High) can be adjusted.

With this Driver you can easily use a Nichia 219AT High CRI or a XP-E (Red?).

This tread might help: link

I used XM-L2 T4 7A3 80+ CRI LED which is very warm tint for my P60. I use it as night light and it is a lot easier on the eyes than cooler tints.
Link

Should be doable with the BLF-VLD driver, just set the modes to 1 and adjust the moonlight to your liking. Where are you located at? I'm sure that there are a few members on here that would be willing to flash the driver for you.

Just out of curiousity, why not just use a really cheap dollar light? They’re practically moonlight straight out of the box.

Hhmmm - interesting application. Wonder what a one 7135 350 mA driver would do with a Nichia? Probably still too high though for your needs. A single mode driver is very easy to build at whatever percentage level you want. With the Nanjg type drivers, you still have to use a minimum level to light up the LED though using PWM's, just not sure how well that will work at a low total amps.

I could do that type of P60 build pretty easily. I'm thinking a low output, nice tint Nichia would be the best running just one 7135, then playing with the PWM's to get the level of output you want - at 350 mA, 5 mA is 1.4%, and for PWM's, lowest you can go is 5 of 256, which is 1.9%. Not sure how this will look, but I do have a KD driver that does a 5 mA, so could compare and test the output in my lightbox. Could also use a XML 3C, which I have laying around, or a true warm tint XML.

Of course would be better if you had a programmable driver, then can set the level you want yourself, so it always comes on in that selected mode.

Thank you for your answers, and the links provided. I discovered DrJones work, and while I don’t understand everything, that seems the way to go! I’m going to give his site a good look :slight_smile:

I’ve already tried to “mess” with the BLF driver firmware, but I was unable to flash my driver board (suspect my Atmel programmer is DOA, I’ve ordered another one for a few $, we’ll see). Besides that, my programming skills are, well, approx to null, so I’d better go with a pre-flashed driver…

As for my location, I’ve added it to my profile :wink: Don’t know if there’s someone around here who can do the programming and/or flashing part for me, but I’ll first contact DrJones.

As for the tint and led model…I’ve got some Nichia 219, and while I really love the tint in a “more normal” use, I prefer other led models for sub-lumen applications. I’ve got a Warm (no idea bin/tint) MC-E in stock (from a trashed el cheapo module), and really like it, nice tint, ugly beam with P60 reflector I have, but I’m going to use a frosted lens anyway. I don’t really like red led (I’ve got some Osram Golden dragon) for night vision, too disturbing for my old eyes !
Other than that, 7A3 tint is amongst my tastes too, and I’ll probably give this led a try (in fact I think I may already have some somewhere). I really liked the tint of old XP-G high CRI (I think the one I had were 90+ CRI and 7B tint, Q2 bin), and I unfortunately don’t find and equivalent tint with the new XP-G2 High CRI leds (I’ve tried Philips Rebel too, they’re on their way).

Well, thank you again for the answers, I’m going to investigate a bit, and I’ll keep you updated :wink:

The USB dongle is the easy part - the ribbon cable with the clip is a bit tricky. I got 2 dongles (the FT one for like $4 or $5 works great), but only one cable. I ported luxdrv to the latest toolset - works great, and mode settings is just a simple table edit job, with high PWM's of 9400.

The FT $4-5 is the one I got. As for the clip, I think (after having carefully examined it when attached to Atmel µcontroller) it is ok. I’m a bit more suspicious about the ribbon cable, and I’ve tried several without result. Since the USB dongle seems a bit sloppy to me (led is red, then off, then on), I suspect it could be bad, I’ll see, i got yesterday a shipping notification from FT for my new dongle :smiley:

I also had trouble with the cable, the one I got was connected from 3-10..

While I thought it was connected from cable 1-8 (2 cables where cut shot by the seller I think)

So I had the cabling done when at last I noted it was in reverse, so I turned the cable plug upside down (with breaking some plastic off the usb dongle otherwise it wouldn't fit)...I figured that out when I saw a little Triangle near one of the legs on the USB dongle, which started me to look things up, and I noticed that that's where cable 1 needs to be connected.

Oh. Man..these things are hard to explain. Good luck on finding the solution.

I’ll say that moonlight (5mA) is a nice party trick to show your friends what an energized emitter looks like, especially on the larger emitters, but for actually projecting light it’s useless. if your night vision isn’t good you still won’t see with this. I would just use one of the 105’s that RMM sell and use the mode set that has a 2% setting.

I disagree…I got many lights with moonlight mode (including Zebralight with several sub-lumen modes), and many modules with Qlite drivers which are said to deliver ~5mA in moonlight mode. You can perfectly look at the emitter (and count the tiny points or the bands, depending on the emitter) and still, at night I found the light produced perfectly usable (just that I tend to change mode too easily) :slight_smile:
My night vision is not that bad, just very long to adapt and easily ruined.
But maybe you’re right, and I can for example darken the lens of my host or something like that and live with the 2% setting…but then I won’t be a real flashaolic, don’t you think (this is me trying a joke in a language I don’t master, sorry) ?

@ ChibiM: Thank you for the suggestion. I also assumed (with the coloured cable and small triangle) that it was connected 1-8, and I tried to move the 8th cable to the 9th position, with no success. In fact connecting 1-8 was shutting off the led of my dongle, and 1-9 seemed to be ok…except no connection. I thought of a lousy connection and double checked all that, but I didn’t checked if it was connected 3-10 instead of 1-8, will do, thanks :wink:

I find moonlight mode plenty useful.

Eat a carrot once in a while.

I juice. I consume more beta keratin every week than Bugs Bunny does in a month. :wink:

I wonder what kind of flashlight Bugs Bunny would carry :bigsmile:

Found your problem!

http://en.wikipedia.org/wiki/Keratin

http://www.flashlightmuseum.com/Eveready-Flashlight-LTEB-Energizer-Bunny-Squeeze-Light-1997

Good find!! too funny!
Ah to be a kid again :slight_smile:

Hi!

Just a heads up to say that I ordered DrJones driver with lucidrv firmware, and I received it today, with some led I ordered from ledtech. Many thanks to DrJones, firmware is perfectly adapted for what I was looking for, relatively easy to program :heart_eyes:
I originally planned to use a warm MC-E, but I screwed up while ordering my leds and ended up with an amber Luxeon (LXML-PL01-0040). Since I found its light quite useful in the dark and easy to dark-adapted eyes, I decided to give it a try!

it is now replacing my old pseudo-regulated incan module (which had a moonlight mode, sort of :D). I first used a reflector for XP-E/XP-G, beam with Luxeon was very floody, with a small donut hole. Than I tried a XR-E reflector, and now there is a huge spot with limited spill…looks good, I’ll see tonight :slight_smile:

Anyone got a current (heh) link for the DrJones pages? The ones in the thread above are giving DynDNS errors.

I’m another amber fan, want to do the same kind of dropin described above.