luminus sbt-90 gen2 led

djozz · 2019-12-13T08:31:44.000Z

Impressive hat

As for the light: clumpsy big thing, but if the reflector is as deep as the length of the head suggests, the beam may have an impressive large spot.

Ilumenati · 2019-12-13T08:27:39.000Z

Astrolux FT03S SBT90.2 4500lm

FT03S

Tom_E · 2019-12-13T15:14:34.000Z

Agro:

They try to do what BLF GT did, that is establish a new, bigger class of lights? I estimate 145-150mm diameter, 8*18650, huge length. BTW these fins are too tight to work well, there will hardly be any airflow between them.

You sure bout those gaps? They could be 5 mm - it's all relative

Hoop · 2019-12-13T15:42:50.000Z

djozz:

if the reflector is as deep as the length of the head suggests, the beam may have an impressive large spot.

Could you elaborate on this djozz?

djozz · 2019-12-13T15:49:49.000Z

Hoop:

djozz:

if the reflector is as deep as the length of the head suggests, the beam may have an impressive large spot.

Could you elaborate on this djozz?

Deep reflectors (compared to shallow reflectors of the same diameter) produce about the same spot brightness but with larger spot, at the expense of spill angle (and it lengthens your flashlight). I like that for a thrower.

Jerommel · 2019-12-13T18:04:28.000Z

Agro:

They try to do what BLF GT did, that is establish a new, bigger class of lights?
I estimate 145-150mm diameter, 8*18650, huge length.

BTW these fins are too tight to work well, there will hardly be any airflow between them.

It seems they never learn…

SKV89 · 2019-12-13T19:04:03.000Z

The gaps in those fins are actually not small if you pay attention. I think it is more than adequate. But that flashlight must weigh 20lbs and doesn’t seem very wieldy. Wonder what the throw is. 5MCD? Would be cool if they can make a RLT collar and aspheric lens to turn it into a 10MCD Enderman light. Under $600 would be a bargain if it makes more than 6MCD.

Jerommel · 2019-12-13T19:13:31.000Z

The gaps are relatively small in relation to their depth.
This means very little airflow between the fins.
The BLF / Lumintop GT has proper fin spacing and not too deep grooves either.

Agro · 2019-12-15T12:04:20.000Z

Jerommel:

The gaps are relatively small in relation to their depth.
This means very little airflow between the fins.
The BLF / Lumintop GT has proper fin spacing and not too deep grooves either.

Right.
What matters is proportions and these are not good.

Tom_E · 2019-12-15T13:18:46.000Z

The BLF GT90 proto is here at 1.8 Mcd, coutesy of Matt (VOB): https://www.youtube.com/watch?v=xQBDrNKyWKY, and here: https://budgetlightforum.com/t/-/59967

Not a significant improvement in throw over the GT (XHP35 HI), he tested at 1.5 Mcd. More lumens of course.

mortuus · 2019-12-15T13:41:29.000Z

this led screams for a GT4 host.

Yokiamy · 2019-12-15T13:46:25.000Z

mortuus:

this led screams for a GT4 host.

This led screams, current give me more current!

Impressive though, the GT90.

Does cree have plans for a XHP35.2 ?

KawiBoy1428 · 2019-12-15T13:59:44.000Z

mortuus:

this led screams for a GT4 host.

It’s going to be expensive with … 4 SBT-90.2’s Then I’m going to want an extension tube (4 carriers) so I can have a battery carrier for each LED… It’s a very HUNGRY LED…

Yes please… :+1:

ttylamg · 2019-12-16T22:23:38.000Z

Can I simply flow the 90.2 on to the existing ft03 board and will it work like that?

EasyB · 2019-12-16T22:42:57.000Z

ttylamg:

Can I simply flow the 90.2 on to the existing ft03 board and will it work like that?

No, it’s a different footprint. It’s similar to the Cree MTG footprint so you can use those MCPCBs.

Jerommel · 2019-12-16T23:08:58.000Z

EasyB:

ttylamg:

Can I simply flow the 90.2 on to the existing ft03 board and will it work like that?

No, it’s a different footprint. It’s similar to the Cree MTG footprint so you can use those MCPCBs.

Here’s a 26mm one:
https://www.aliexpress.com/item/32601399686.html

Mike_C · 2019-12-17T14:32:49.000Z

With such an expensive emitter I would prefer them pre-mounted. Tom E wrote “They come pre-mounted on a 20 mm MCPCB, $36 each.”
I wasn’t able to find any details on lantend.com about that. Has anyone received any pre-mounted yet?

EasyB · 2019-12-17T16:32:20.000Z

Mike C:

With such an expensive emitter I would prefer them pre-mounted. Tom E wrote “They come pre-mounted on a 20 mm MCPCB, $36 each.”
I wasn’t able to find any details on lantend.com about that. Has anyone received any pre-mounted yet?

Yes that is probably an option. For me by default they came bare. I didn’t know the quality of their MCPCBs or their reflow, so I figured I would rather get them bare. Have to check with Tom E about whether he got them on MCPCBs.

Jerommel · 2019-12-17T17:47:24.000Z

So where can i obtain one of these LEDs for a reasonable price?
Or do i have to buy a complete NI40 light?
You see, i have this ginormous GT flashlight here, and the XHP35 HI is just too small for it.
If i could get a SBT-90.2 for it, it would be awesome.
I’ll worry about the driver later.
Maybe the stock driver could be adapted with a stack of FETs, a huge toroid coil and fat flyback diodes.

Jerommel · 2019-12-17T17:48:54.000Z

SHouldn’t there be a group buy for these LEDs?