new Emisar with 18 SST20 and 14kLumen

M4D_M4X · 2019-03-14T05:56:31.000Z

looks like a M43 Mini

VrestoTaylor · 2019-03-14T05:57:25.000Z

Power source? 26650?its bigger…

mattadores · 2019-03-14T05:57:58.000Z

You had me at “New Emisar”

Johm · 2019-03-14T06:19:11.000Z

vresto:

Power source? 26650?its bigger…

Looks more like 3x18650

toddcshoe · 2019-03-14T06:22:21.000Z

Nice!!!

Does it come with a deep carry pocket clip?

AlexGT · 2019-03-14T06:31:40.000Z

Ouch!!! That thing looks sharp…!!! I really don’t like it there, why not make a hole on the opposite side of the switch in one of the fins???

clientequator · 2019-03-14T07:08:08.000Z

Wow this is the new ‘noctigon meteor’ to beat! I don’t see it on intl-outdoor.com but this is looking to be very amazing!!

Rusty · 2019-03-14T07:10:48.000Z

Looks good - Aux LED’s?

dmsoule · 2019-03-14T07:20:42.000Z

Johm:

vresto:

Power source? 26650?its bigger…

Looks more like 3x18650

Or 3x21700 maybe?

thisnameisvalid · 2019-03-14T07:27:52.000Z

Looking good! I think it might use 18650s… The body tube looks quite thick with that lanyard hole

kiriba-ru · 2019-03-14T07:34:56.000Z

AlexGT:

Ouch!!! That thing looks sharp…!!! I really don’t like it there, why not make a hole on the opposite side of the switch in one of the fins???

The reasons were discussed in Q8 thread.
Most cheap can-shape flashlights a machined without threads synchronization. I.e. switch place is milled with separate machine or separate setup and have random position relative to the threads start point.
Battery tube is made with same way.
As result you have random angle between switch and tube flatness.
In Q8 design this problem is even bigger than ever, because tube end forces down the driver pcb so tube angular position depends from driver thickness.
Using combine machines with minimum setups can fix this problem, but sometimes design is not suitable for this.
If flashlight have a removable tail cap (as Q8 have), a spare lanyard ring that can freely rotate looks like cheap and easy solution.

ToyKeeper · 2019-03-14T07:48:27.000Z

Well, I guess that cat is out of the bag…

I should have one to review sometime soonish. I also have an incomplete prototype strictly for firmware development. Just finishing up the last few details now, actually. I don’t think I can really give any extra details about it yet though.

What I can say is … it’s really bright. Like, really really bright. I can’t even measure it properly, because it’s way more lumens than I have equipment for. It’s like a Noctigon Meteor M43 but a bit smaller, a lot brighter, and with the Emisar UI people liked on the D4S. So if anyone was wanting a “Meteor 2”, this is probably for you.

sp5it · 2019-03-14T08:14:01.000Z

Famous shower head flashlights are back, jupiiii

oweban · 2019-03-14T08:27:08.000Z

… and just when my MF01 arrived

VrestoTaylor · 2019-03-14T08:31:54.000Z

I guess 4x 18650…

M4D_M4X · 2019-03-14T08:38:01.000Z

https://budgetlightforum.com/t/-/55963

official thread

nokoff · 2019-03-14T10:54:45.000Z

ROT66 killer/

Agro · 2019-03-14T11:10:45.000Z

Would be interesting to see it next to ROT66. I suppose it’s larger?

lightboks · 2019-03-14T11:24:57.000Z

Agro:

Would be interesting to see it next to ROT66. I suppose it’s larger?

d18: head 58mm, body 46mm, height102mm. 3x18650

Wieselflinkpro · 2019-03-14T11:46:23.000Z

lightboks:

Agro:

Would be interesting to see it next to ROT66. I suppose it’s larger?

d18: head 58mm, body 46mm, height102mm. 3x18650

ROT66: head 49mm, body 45mm, height 110mm, 3x18650

D18 is shorter and thicker at the head. Body is similar.