No power on MTN 17DDM driver

raccoon · 2019-07-14T00:07:07.000Z

How about resizing that second pic to 100% wide?

trailhunter · 2019-07-14T00:12:27.000Z

There we go, apparently passing over _d as part of the resize actually resizes the photo

e1000 · 2019-07-14T00:30:41.000Z

After the driver is hooked up, are you sure the LED’s aren’t on? First mode maybe ML, and with something like this driver on a triple, ML will be very very low.

Mark_M · 2019-07-14T00:34:50.000Z

Maybe you were sent a version with electronic switch firmware? Have you tried putting a switch on pin 2? I can’t remember if my eswitch version flashed the LEDs when connected to power.

KawiBoy1428 · 2019-07-14T00:55:42.000Z

Is the driver tight when the retainer ring is tightened?

. *We will be transitioning from1.2mm PCBs* to 1.6mm PCBs on the MTN-17DDm

The transition will happen as current 1.2mm stock runs out. This transitional period may take a few months

Did you solder that negative lead onto the FET? Or did you get the leads already installed?

trailhunter · 2019-07-14T01:01:55.000Z

KawiBoy1428:

Is the driver tight when the retainer ring is tightened?

. *We will be transitioning from1.2mm PCBs* to 1.6mm PCBs on the MTN-17DDm

The transition will happen as current 1.2mm stock runs out. This transitional period may take a few months

Did you solder that negative lead onto the FET? Or did you get the leads already installed?

I soldered the leads from the mcpcb.

Its tightened down. I also used a power supply and touched the leads directly to the drivers positive and ground and nothing.

trailhunter · 2019-07-14T01:13:25.000Z

Mark M:

Maybe you were sent a version with electronic switch firmware? Have you tried putting a switch on pin 2? I can’t remember if my eswitch version flashed the LEDs when connected to power.

I havent tried. Even if I tap the power supply leads, it wouldn’t switch?

trailhunter · 2019-07-14T01:13:57.000Z

e1000:

After the driver is hooked up, are you sure the LED’s aren’t on? First mode maybe ML, and with something like this driver on a triple, ML will be very very low.

Yeah definitely sure. Hmm what gives

KawiBoy1428 · 2019-07-14T01:15:44.000Z

trailhunter:

KawiBoy1428:

Is the driver tight when the retainer ring is tightened?

. *We will be transitioning from1.2mm PCBs* to 1.6mm PCBs on the MTN-17DDm

The transition will happen as current 1.2mm stock runs out. This transitional period may take a few months

Did you solder that negative lead onto the FET? Or did you get the leads already installed?

I soldered the leads from the mcpcb.

Its tightened down. I also used a power supply and touched the leads directly to the drivers positive and ground and nothing.

I have had problems with the thinner boards (1.2mm PCB’s)not making ground, probably why he is going back to the 1.6mm boards, the retainer ring would bottom out and the driver felt tight but wouldn’t be tight enough to make ground.

Assemble everything outside the pill and see if it works….touch your power supply leads to the spring and ground ring on the driver momentarily to see if it works…

Maybe the FET is fried from too much heat?

trailhunter · 2019-07-14T01:21:11.000Z

KawiBoy1428:

trailhunter:

KawiBoy1428:

Is the driver tight when the retainer ring is tightened?

. *We will be transitioning from1.2mm PCBs* to 1.6mm PCBs on the MTN-17DDm

The transition will happen as current 1.2mm stock runs out. This transitional period may take a few months

Did you solder that negative lead onto the FET? Or did you get the leads already installed?

I soldered the leads from the mcpcb.

Its tightened down. I also used a power supply and touched the leads directly to the drivers positive and ground and nothing.

I have had problems with the thinner boards (1.2mm PCB’s)not making ground, probably why he is going back to the 1.6mm boards, the retainer ring would bottom out and the driver felt tight but wouldn’t be tight enough to make ground.

Assemble everything outside the pill and see if it works….touch your power supply leads to the spring and ground ring on the driver momentarily to see if it works…

Maybe the FET is fried from too much heat?

Bummer, still nothing. I got 2 more drivers I’ll try them out. But 2 of 4 is kinda weird

Mark_M · 2019-07-14T01:22:39.000Z

trailhunter:

Mark M:

Maybe you were sent a version with electronic switch firmware? Have you tried putting a switch on pin 2? I can’t remember if my eswitch version flashed the LEDs when connected to power.

I havent tried. Even if I tap the power supply leads, it wouldn’t switch?

Nope.

trailhunter · 2019-07-14T01:28:17.000Z

trailhunter:

KawiBoy1428:

trailhunter:

KawiBoy1428:

Is the driver tight when the retainer ring is tightened?

. *We will be transitioning from1.2mm PCBs* to 1.6mm PCBs on the MTN-17DDm

The transition will happen as current 1.2mm stock runs out. This transitional period may take a few months

Did you solder that negative lead onto the FET? Or did you get the leads already installed?

I soldered the leads from the mcpcb.

Its tightened down. I also used a power supply and touched the leads directly to the drivers positive and ground and nothing.

I have had problems with the thinner boards (1.2mm PCB’s)not making ground, probably why he is going back to the 1.6mm boards, the retainer ring would bottom out and the driver felt tight but wouldn’t be tight enough to make ground.

Assemble everything outside the pill and see if it works….touch your power supply leads to the spring and ground ring on the driver momentarily to see if it works…

Maybe the FET is fried from too much heat?

Bummer, still nothing. I got 2 more drivers I’ll try them out. But 2 of 4 is kinda weird

Ok 3 of 4 dont work.

Mark_M · 2019-07-14T01:34:20.000Z

For what it is worth I have ordered 7 drivers from Richard and none of them were defective, there is something else wrong. Get a multimeter out and test the voltage to the microcontroller. If there is voltage to the microcontroller but not the pin that controls the FET then it is a firmware/switch issue.

KawiBoy1428 · 2019-07-14T01:47:03.000Z

This is an e-switch driver in this picture…

trailhunter · 2019-07-14T01:45:02.000Z

KawiBoy1428:

This is an e-switch driver in this picture…

Crap, how can you tell?

KawiBoy1428 · 2019-07-14T01:57:02.000Z

trailhunter:

KawiBoy1428:

This is an e-switch driver in this picture…

Crap, how can you tell?

Sorry, I meant is this an e-switch driver, it should have come with this if it was…

Mark_M · 2019-07-14T02:02:16.000Z

KawiBoy1428:

trailhunter:

KawiBoy1428:

This is an e-switch driver in this picture…

Crap, how can you tell?

Sorry, I meant is this an e-switch driver, it should have come with this if it was…

So I have ordered two of these drivers that came with a capacitor installed instead of the pads being bare, and no note. When I contacted Richard he said the capacitor helped with noise, this was last year some time.

trailhunter · 2019-07-14T02:23:15.000Z

KawiBoy1428:

trailhunter:

KawiBoy1428:

This is an e-switch driver in this picture…

Crap, how can you tell?

Sorry, I meant is this an e-switch driver, it should have come with this if it was…

Mine didnt come with that. This is what I ordered FET + 7135 Driver - 17mm - MTN-17DDm

Is this an e-switch driver? For now I put a v54 driver. Fricken light is pulling 12amps on high :zipper_mouth_face:

trailhunter · 2019-07-14T02:43:34.000Z

Crap guys, so thanks for narrowing it down. Apparently I ordered all the drivers with biscotti firmware. I should be able to reflash with guppy or other firmware right?

FML.

KawiBoy1428 · 2019-07-14T03:11:31.000Z

trailhunter:

KawiBoy1428:

trailhunter:

KawiBoy1428:

This is an e-switch driver in this picture…

Crap, how can you tell?

Sorry, I meant is this an e-switch driver, it should have come with this if it was…

Mine didnt come with that. This is what I ordered FET + 7135 Driver - 17mm - MTN-17DDm

Is this an e-switch driver? For now I put a v54 driver. Fricken light is pulling 12amps on high :zipper_mouth_face:

The only way you can tell is to hook it up, it would be in the firmware of the MCU….if they got mixed up?

I ordered a bunch of drivers 10-12 different drivers, maybe 1.5-2 months ago and they all came with detailed stickers on them.