The XHP70.2 8,000 Lumen BLF-GT With Beam Shots!!!!!!!

PiercingTheDarkness · 2019-02-18T10:37:51.000Z

That’s great news. Thank you

djans1397 · 2019-02-23T19:44:30.000Z

Hi all!

So I’ve read this entire thread. I’m ready to convert my XHP35. I’ve ordered Neal’s kit, CW version. I guess it comes with the battery carriers, though I don’t need them. Is this going to be a direct drive board like the second one Matt used in his video?

I’ve watched Matt’s video. I’ve never modded a light, but have enough skills to do so I think. A simple soldering iron and solder and flux should be all I need right? I don’t want to screw anything up, so ANY Tips or advice prior would be much appreciated from anyone in here.

I’m super stoked to do this and can’t wait to try it out.

Thanks in advance everyone!

Daniel

Texas_Ace · 2019-02-23T19:51:29.000Z

Yeah, with the kit you basically just have to solder the LED power wires and you should be good to go.

Be careful to clean the LED carefully with alcohol before testing. even the smallest spec can kill the LED.

djans1397 · 2019-02-23T19:54:54.000Z

Ok. Thanks much.

Is this DD?

What’s the verdict on dedoming? Good, bad?

Texas_Ace · 2019-02-23T19:56:58.000Z

Yes, the driver that comes with the kit is a FET based driver.

I personally don’t like dedomed LEd’s but it does throw a lot further that way.

djans1397 · 2019-02-23T20:02:15.000Z

Parson my ignorance, FET driver is a direct driver?

Texas_Ace · 2019-02-23T20:03:34.000Z

Correct

lawallac · 2019-02-23T21:04:27.000Z

djans1397:

Hi all!

So I’ve read this entire thread. I’m ready to convert my XHP35. I’ve ordered Neal’s kit, CW version. I guess it comes with the battery carriers, though I don’t need them. Is this going to be a direct drive board like the second one Matt used in his video?

I’ve watched Matt’s video. I’ve never modded a light, but have enough skills to do so I think. A simple soldering iron and solder and flux should be all I need right? I don’t want to screw anything up, so ANY Tips or advice prior would be much appreciated from anyone in here.

I’m super stoked to do this and can’t wait to try it out.

Thanks in advance everyone!

Daniel

It would be a good idea to get a very small amount of good thermal compound like Arctic Silver5 or similar.

JasonWW · 2019-02-23T23:13:11.000Z

djans1397:

Hi all!

So I’ve read this entire thread. I’m ready to convert my XHP35. I’ve ordered Neal’s kit, CW version. I guess it comes with the battery carriers, though I don’t need them.

Neal’s kit does not include the carriers. They are a $38 option.

Make sure you can get the upper head and bezel loose. This might be the hardest part of the conversion.

Jon844989 · 2019-06-16T14:33:57.000Z

I apologize if I am using this forum incorrectly. I simply wanted to post a question regarding my BLF GT70. It seems that it won’t ramp up to the full high mode .When I ramp up it barely gets any brighter . And when I get double click for turbo it comes up to what seems like the current ramped up mode. All batteries are fresh and fully charged. And I’ve attempted to a factory reset. I’m not sure if the issue lies in the programming or of something is broken internally . Plz helps

Texas_Ace · 2019-06-16T15:37:31.000Z

If it maxes out around a few hundred lumens, then most likely the 2nd channel is not coming online for some reason.

Did it ever work properly?

The most likely cause is a bad FET. Luckily this is fairly easy to replace if you have any soldering skill. If not then a replacement driver should get it working. Lumintop should be able to get you one.

PiercingTheDarkness · 2019-06-17T10:47:11.000Z

I assume you’re using good brand cells?

Theodore41 · 2019-06-17T11:21:33.000Z

Hi vestureofblood .
I have a Astrolux MF04S instead of the BLF XHP70.2 and a Astrolux MF-04 as well. Is there a possibility to have a similar update?I have a BLF-GT as well.
So,if I wanted to push one of them,so as to be like yours,which one is better and what parts I had to find?

Lumencraft-Matt · 2019-06-17T19:12:41.000Z

Theodore41:

Hi vestureofblood .
I have a Astrolux MF04S instead of the BLF XHP70.2 and a Astrolux MF-04 as well. Is there a possibility to have a similar update?I have a BLF-GT as well.
So,if I wanted to push one of them,so as to be like yours,which one is better and what parts I had to find?

I have not had an MF04S apart so I cant say for sure about boosting the driver. I am gussing you will find a buck driver inside so if you take a picture of the board components and post it,there may be a sense resistor that can be changed on it to give you a bit more current. As for getting more throw, you could definitely slice the dome off your LED and get a huge jump in performance.

If the Astrolux driver can not be boosted, Lumintop doe sell a driver and LED kit for the BLFGT to convert it to 70.2 and the mosfet. BLF GT70 Conversion Kits – Nealsgadgets

JasonWW · 2019-06-17T20:48:29.000Z

The MF04S uses a Boost driver (6v to 12v mcpcb). You can change sense resistors to boost output, but Turbo run times drop from around 1 minute down to 30 seconds. Most modders just replace the driver to get a better user interface. With NarsilM or Anduril you have full control over the thermal step downs.
Lexel makes a regulated driver for it and I also think a FET driver.
See this thread.

What kind of extra performance are you looking for? More distance on the MF04S? Slicing the dome will do that. The MF04 and GT are already maxed out for distance.

Jon844989 · 2019-06-17T22:03:31.000Z

Yes it worked properly . I suppose I can start there

Jon844989 · 2019-06-21T04:36:05.000Z

Does anybody know where to get parts for the BLFGT70? I need the battery holders that go in the flashlight . I apologize if I didn’t post this in the correct area of the forum as I am new to it.

trailhunter · 2019-06-21T05:10:18.000Z

Jon844989:

Does anybody know where to get parts for the BLFGT70? I need the battery holders that go in the flashlight . I apologize if I didn’t post this in the correct area of the forum as I am new to it.

Nealsgadgets

BLF GT70 Conversion Kits

GT70 Conversion Kits are for GT70 DIY. 1*XHP70.2 LED, Cold white or Neutral white options 1*Centering Ring 1*TA Driver Giggle Monster 2*Cell carriers

Price: USD 14.00

Gofastdodge · 2022-10-15T17:59:52.000Z

I’m having an issue with my gt70. Seems to be same problem as Jon844989, top of ramp is not as bright as it should be, and no turbo, no strobes, accept the 3rd one… if I double click, led goes off… double click for turbo. Nothing, click few times, one strobe would work… It’s strange. I’ve re-flowed the driver board. Ive replaced the mosfet. I switched The 8 pin controller with Another light to see if it works. I’ve tried different leds. I’ve tightened the battery carrier’s. I will mention, I have double springs, and braided copper strands in carrier’springs. Could I fried something having to low resistance?. I’ve had it like this for 2 years… and it just did this out of nowhere. Getting frustrated… any ideas?..

Texas_Ace · 2022-10-15T18:05:10.000Z

If the lower levels work fine and it is only the brightest levels, sounds like a mosfet issue, the lower levels are handled by the resistor bank. The high modes are handled by the dedicated FET.

You said you replaced it but something with that FET makes the most sense. If you have reflowed the driver, it is possible one of the resistors or pins leading to that FET was messed up and is preventing the FET from getting the signal.