Would there be enough material in the tail switch to put a slot for a trit (like the reylights)?
Answered here.
ToyKeeper wrote:
contactcr wrote:
Can we machine a trit slot in the tail switch?
Probably not. Every part of this light, including the button, is thinned down enough that a trit slot would likely go all the way through the metal. The only place I know trits could fit is under the optic. It’s also possible that some might fit in the thick part of the tapered body tube.
Most lights have a lot of extra material to drill into, but this one does not. It opts to be smaller rather than unnecessarily thick.
—
Texas Ace Lumen Tube and JoshK Sphere calibrated with Maukka lights
Was there an updated rendering anywhere buried in the thread?
If not, based on the original rendering in post one, the tail button is around 2mm thick. That would require a person modding the light to take quite a bit of care cutting the slot for a 6mm x 1.5mm tritium vial to sit flush without breaking through.
The thick part of the tailcap surrounding the button is about 4mm x 4.5mm, so that’s a potential location.
The shoulders on either end of the body tube are about 2.5mm x 3mm.
Ok. I’ll just get trit optics then. Thanks for the info.
Toykeeper’s info about the driver (with the upgraded 7135 chips)!just blows me away. This is shaping up to be amazing. I’m putting my money where my mouth is too, I’m signned up for three!
Hi, I'm listed as being down for four (4) lights, but I only asked for two (2). I've only ever made one request post for two (2). See my history, it's pretty short.
(Not sure what happened. I had to double-check this to make sure I wasn't losing my mind. )
Hi, I’m listed as being down for four (4) lights, but I only asked for two (2). I’ve only ever made one request post for two (2). See my history, it’s pretty short.
(Not sure what happened. I had to double-check this to make sure I wasn’t losing my mind. )
So… Opened the 200+ new post, and accidentally closed it, and then lost track where I left off.
Read the 5 or so newest pages.
Was there a decision on anodizing? How about emitter and temp? Or at least what emitter and temp was most voted for?
Sorry, try to avoid these types of posts, but made a stupid mistake of putting off catching up on the thread and allowing 200+ posts to go by, and closed it by accident when I did get around to checking it…
So… Opened the 200+ new post, and accidentally closed it, and then lost track where I left off.
Read the 5 or so newest pages.
Was there a decision on anodizing? How about emitter and temp? Or at least what emitter and temp was most voted for?
Sorry, try to avoid these types of posts, but made a stupid mistake of putting off catching up on the thread and allowing 200+ posts to go by, and closed it by accident when I did get around to checking it…
No anodizing decision yet.
No emitter decision yet.
You can see the poll results on post #1.
It looks like 5000K temp and xpl-hi is most popular.
—
Texas Ace Lumen Tube and JoshK Sphere calibrated with Maukka lights
After 14 months this group buy must be one of the slowest BLF has ever had.
While I am definitely looking forward to it, I think it’ll still be my second choice after the D4. Maybe third choice after the D4 is rereleased in 26650 format…
After 14 months this group buy must be one of the slowest BLF has ever had.
It has definitely been frustratingly slow. I think it’s pretty close, but at the moment I think it’s hung up on some miscommunication about thermal regulation. I’ve been trying to resolve that for a few weeks, but too much gets lost in translation. It feels like when Ford Prefect wrote an entire detailed guide about how to enjoy planet Earth, and the editor shortened his work to just two words — mostly harmless. It’d be a lot easier if I could talk directly to the engineers at Lumintop instead of going through a communication gatekeeper.
(snip)
It’d be a lot easier if I could talk directly to the engineers at Lumintop instead of going through a communication gatekeeper.
Lick wrote:
Lumintop people are pretty active on facebook and their english seems ok. Why is it a problem? Have you brought it up to them?
It seems that its been very slow but it looks great. Appreciate the update TK, I love your UIs!
Just taking a guess at it… the one’s active on FaceBook are most likely also the “communication gatekeepers” TK is talking about.
It may be slow, but I agree…. it is looking good!! .
—
You never know how a horse will pull until you hook him up to a heavy load./"Bear" Bryant
.................................. "Slow is Smooth, Smooth is Fast" ...................................
Hi, I'm listed as being down for four (4) lights, but I only asked for two (2). I've only ever made one request post for two (2). See my history, it's pretty short.
(Not sure what happened. I had to double-check this to make sure I wasn't losing my mind. )
Will there be any space for trits in this light?
From previous post I read, it does not have extra material to fit any
Well, you could use some of these drilled optics from azhu in his WTS thread.
The Cycle of Goodness: “No one prospers without rendering benefit to others”
- The YKK Philosophy
Would there be enough material in the tail switch to put a slot for a trit (like the reylights)?
Texas Ace Lumen Tube and JoshK Sphere calibrated with Maukka lights
Click this to go to signature links. I'm still around, just not reading many new threads.
Was there an updated rendering anywhere buried in the thread?
If not, based on the original rendering in post one, the tail button is around 2mm thick. That would require a person modding the light to take quite a bit of care cutting the slot for a 6mm x 1.5mm tritium vial to sit flush without breaking through.
The thick part of the tailcap surrounding the button is about 4mm x 4.5mm, so that’s a potential location.
The shoulders on either end of the body tube are about 2.5mm x 3mm.
Maybe a number of smaller tubes? Fasttech has even 2×0.5 mm. Or 6.6×0.65.
Ok. I’ll just get trit optics then. Thanks for the info.
Toykeeper’s info about the driver (with the upgraded 7135 chips)!just blows me away. This is shaping up to be amazing. I’m putting my money where my mouth is too, I’m signned up for three!
Hi, I'm listed as being down for four (4) lights, but I only asked for two (2). I've only ever made one request post for two (2). See my history, it's pretty short.
(Not sure what happened. I had to double-check this to make sure I wasn't losing my mind.
)
Thanks.
Hey, darrylo, you ordered four (4) flashlights.
.
Check it out, click on the links
See Post: #1250, page 42, : Tue, 09/05/2017 .
The Miller gave him number 588 and 589 on Interest List. TK moved it to 586 and 587 See Post # 4, Page 1 .
.
See Post: #2132, page 72, Wed, 01/10/2018 .
pepinfaxera gave him number 931 and 932 on Interest List. T.K. left him at 931st and 932nd on the List of Interest See Post # 4, Page 1 .
If it was a mistake, no problem.
I’ll take two from you.
I’ll give you two, numbers 586 and 587.
Sorry for my bad English
(google translator) , (https://www.deepl.com/translator)
So… Opened the 200+ new post, and accidentally closed it, and then lost track where I left off.
Read the 5 or so newest pages.
Was there a decision on anodizing? How about emitter and temp? Or at least what emitter and temp was most voted for?
Sorry, try to avoid these types of posts, but made a stupid mistake of putting off catching up on the thread and allowing 200+ posts to go by, and closed it by accident when I did get around to checking it…
-the- Throw calculator - Pulsars list
No anodizing decision yet.
No emitter decision yet.
You can see the poll results on post #1.
It looks like 5000K temp and xpl-hi is most popular.
Texas Ace Lumen Tube and JoshK Sphere calibrated with Maukka lights
Click this to go to signature links. I'm still around, just not reading many new threads.
Sounds good to me
Saw someone posted they don’t care about anno, so wasn’t sure if more was talked about it or not.
-the- Throw calculator - Pulsars list
Put me down for one please!!!!
I'm in for 1!
Quick question, will this light have a beacon function (a single flash a couple of second apart)?
Beacon: Blink once every N seconds at the last-ramped level. N is configurable.
Check out this post: http://budgetlightforum.com/comment/1120495#comment-1120495
Yes is the short answer, but you can see the rest of the functions there.
Also link to development thread:http://budgetlightforum.com/node/56105
Nice!
Thanks for the confirmation and info
Please count me in for 1, can’t beat the price and what you get.
---------------------
Hoarding is a behavior where people or animals accumulate food or other items.
Late to the party but put me on the list for one please.
RIP SPC Joey Riley, KIA 11/24/14. Now I am become death, the destroyer of worlds.
In for one
I’m also in for one
After 14 months this group buy must be one of the slowest BLF has ever had.
While I am definitely looking forward to it, I think it’ll still be my second choice after the D4. Maybe third choice after the D4 is rereleased in 26650 format…
It has definitely been frustratingly slow. I think it’s pretty close, but at the moment I think it’s hung up on some miscommunication about thermal regulation. I’ve been trying to resolve that for a few weeks, but too much gets lost in translation. It feels like when Ford Prefect wrote an entire detailed guide about how to enjoy planet Earth, and the editor shortened his work to just two words — mostly harmless. It’d be a lot easier if I could talk directly to the engineers at Lumintop instead of going through a communication gatekeeper.
^ It’s still an improvement. It used to just say “harmless,” which arguably is not quite an accurate description of lights like these.
Lumintop people are pretty active on facebook and their english seems ok. Why is it a problem? Have you brought it up to them?
It seems that its been very slow but it looks great. Appreciate the update TK, I love your UIs!
Just taking a guess at it… the one’s active on FaceBook are most likely also the “communication gatekeepers” TK is talking about.
It may be slow, but I agree…. it is looking good!!
. 
You never know how a horse will pull until you hook him up to a heavy load./"Bear" Bryant
.................................. "Slow is Smooth, Smooth is Fast" ...................................
Texas Lumens Flashlights / M4D M4X Deals : sign up - save $$$$
Rudeness Level _ mΩ _ {width:70%} _ LightWiki _ LED Tint Chart
Xlamp size chart _ BatteryU _ Flashaholic? Need Professional Help??? TheOriginal _ TAB _ LightSearch _ BatterySearch _ 14500's _ DiCal
In for one!
I am in for one!
OK, I'm obviously an idiot.
I'd rather have only two (2). However, if that will cause any problems, I will buy four.
Thanks.
Pages