Nice pics from proto 3! But correct me if i am wrong I thought that we get the 3 bladed tailcap. On the pics i see something else.
I pointed this out a couple days ago, but got no response. I’m assuming the 3 blade is gone.
Yes, the 3-blade design is gone, Miller asked to bring it back in the final version and unexpectedly that appeared quite a problem for Thorfire. Because it was not really a big deal we did not ask further to find out what was so difficult about it and left it at that.
I would like one, please add to the list :sunglasses:
Thanks!
LVP should not be kicking in after only a minute of use. Even with only 2 cells it should last quite a bit longer then that if they were fully charged when you turned it on.
I have run my 10K lumen SRK’s with a single cell before and it didn’t step down in the few minutes I plaid with it (was trying to see how hot it got with only one cell).
Yeah, that doesn’t make sense:
Two GA:s (fully charged) should (easily) be able to deliver 20A without too much voltage drop, even 30A for a while (until they get too hot).
Check HKJ:s test:
I have two protected GA’s (Enerpower), I will repeat Miller’s test once they are charged up.
Westbam, yes will update list later.
Hey I did not say LVP kicked in after 1 minute, I said stepdown
Have not done a full runtime test for can’t get the ceiling bounce app to work.
Stepdown is the name for turbo stepdown.
Sure the GAs were used a lot when the LVP kicked in lol
Sorry JasonWW, I remember reading your post and thought I reacted via quote, must have turned off the phone before it was actually posted, apologies.
Yes what Djozz said, we did not ask about it, also from my point of view others said they liked the four blade and this is not important in function and even for not the most looked at section.
Oh come on….
OK I used the Q8 with 2 cells GA
At a certain time it blinked 3 times and went to a lower mode.
I grabbed the phone and started stopwatch, results see above.
After 12 hours I stopped to see what the voltage of the cells were (Q8 was shining to bright to look directly in the LEDs but not very bright) and they were 3,14V
Sorry for being picky, but you did write LVP.
No biggie though, now that you have cleared it up.
I was just worried that there might be something wrong with the LVP.
No, this is what I wrote
I really hate being this picky, but you actually wrote: It kicked in LVP
Check yourself in the post above.
Yeah Wim, sorry, but that is what you said… it’s clearly written above and even quoted…
“Wow using only 2 GA cells
It kicked in LVP
So I started stopwatch ”
Heheh yeah before the runtime test on LVP it had kicked in LVP, kind of hard to do a test on LVP if it is not in LVP 
All the way down, below my results I described how I would like to do a run test with the ceiling bounce app, and there I write setting stepdown at 1 minute for keeping the temp nice and low. Stepdown, it yeah it is tricky and glad it is clear now
But there’s a lesson in there, this firmware is VERY customizable, set it up as you wish, change it at will… Good news all around. 
Yeah and with at least 12 hours of light AFTER LVP a pretty nice emergency light.
I was impressed when I did the S70 review and I could squeeze some time on non darkness out of it when it kicked into LVP
Man 12 hours and much more if I had set it to a 7135 only mode first “LVP kickdown” and if there had been 4 cells in there.
hate to be a pain, but where is order list to confirm/count my count so I can check to order more ?
Good work on the light , guys…
A long time in coming but looking GOOD…
Trump’s latest…Ban shredded cheese…Make America grate again…
post #1
You are listed once (#265) which means one unit.
Thanks JasonWW, yeah indeed check list in post 1
Ah and the list also says to what post it is updated, after that will be done next time