Thank you
fwiw, Lumintoplighting has FWAA Ti Stonewashed bezels for $8ā¦ ordered a coupleā¦
and, TS10 in Red host now in stock, and factory firmware updated
Thank you
fwiw, Lumintoplighting has FWAA Ti Stonewashed bezels for $8ā¦ ordered a coupleā¦
and, TS10 in Red host now in stock, and factory firmware updated
I am just amazed at all the people that managed to get the bezel off the TS10. Iāve been trying to get the bezel off mine since the first day I got it and it just wonāt budge. Iāve tried using the rubber sole of a boot as well as a pair of gloves. I even tried a pair of pliers but Iām afraid of applying too much pressure and deforming the aluminum. Is there some sort of tool that can get the bezel off?
I am just amazed at all the people that managed to get the bezel off the TS10. Iāve been trying to get the bezel off mine since the first day I got it and it just wonāt budge. Iāve tried using the rubber sole of a boot as well as a pair of gloves. I even tried a pair of pliers but Iām afraid of applying too much pressure and deforming the aluminum. Is there some sort of tool that can get the bezel off?
Most of the threadlock compounds and glues that manufacturers use will soften up nicely with a little heat. You could try running it on turbo for awhile, bump it up a few times, then immediately try to unscrew the bezel. It usually wonāt break loose immediately but if you maintain strong pressure it might just let go. If not then you could try longer/higher heat with a hair dryer or heat gun on a lower setting (donāt want toooo much heat and you donāt want to discolor the anodizing either). There are some clever slotted bezel clamp wrench things (I think it was HDS that made some for their models) that you could make easilyā¦slab of material that can flex a little, hole drilled to match the bezel size, and a v-slot cut into it so that when squeezed the bezel hole will shrink a little and provide even clamping pressure. Similarly you could cut some wood v-blocks to use in a vise but then you also need something to twist the head withā¦and they make some good polyurethane vise pads these days, too, usually with a 1/2ā or 5/8ā hole that will grip this light nicely (position it in the center of the jaws). On the TS10 there isnāt anything to provide purchase like flats or a hump, so itās more difficult and popular strap wrenches are a bit too wide. Just be cautious with clamping because itās surprisingly easy to bend the thin aluminum in most lights and thereās no good way to make it round again (which can be fine, but it could also make it where you canāt screw the bezel on again or even not be able to fit the lens in there (or could break the lens)). But try some gentle or medium heat first. Donāt try any solventsā¦if they even get down there you run the risk of vapors affecting the emitters (or the aluminized surface in reflector lights). Also, when it budges, go carefully and be sure that the optic isnāt going to twist with the bezel and shear off the emitters from the boardā¦can press down on the lens a time or two as you unscrew to help there if needed.
I may have been wrong about HDS and those wrenchesā¦they donāt show them on their site now anyway. Hereās the same thing from Four Sevens/Prometheus/Dark Sucksā¦ā¦easy to make.
the right tool for the job is the only tool for the job We use these wrenches in the shop to build and repair lights. Now we are making them available to the public.Ā I got the idea from @robinrenzetti on Instagram. He's a master of all...
Iāve been trying to get the bezel off mine since the first day I got it
this is how the OP does it What did you mod today? - #11294 by Firelight2
Why do you want to take the bezel off?
tried a pair of pliers but Iām afraid
Regardless what tool I use, the secret to My success is heat.
Put the light in the sun for an hour, or put boiling hot water in a cup, then dip half the bezel into the water for a few seconds. If you do not trust the O ring, put the light in a plastic bag first.
You are right to be afraid of turning a circle into an oval using pliers. I leave the body installed when clamping, precisely to help prevent crushing the head tube.
these vise grips are my weapon of last resort:
.
fwiw, the bezel tools that darksucks and Oveready sell, are too big for TS10:
You could try Strap Wrenches:
.
Harbofreight has strap wrenches for very little money. Tip: wipe down the rubber straps with alcohol, otherwise theys tend to slipā¦ they are a fiddly tool, but its good to have options.
Iām trying to possibly do an emitter swap. Iāll definitely try adding heat, perhaps with the heat gun I have in my house. Also, I never knew strap wrenches existed until now. Just bought one on Amazon. Even if it doesnāt work for the TS10, thereās quite a few other things in the house that it will be useful for, thanks for the tip!
Iām trying to possibly do an emitter swap.
cool, Nichia E21a works
Walmart has them too. Much safer (for the light) than with slip-joint or visegrips. And look at all that glue!
congratulations!
why did you open it?
Because the TS10ās driver is substantially thinner than the FWAAās driver, I cut a couple washers from copper sheet to lift the star to the correct height. These washers are layered between the star and the shelf with Arctic Silver 5 thermal grease between all of them.
Hey @Firelight2 !
Sorry, but do you happen to have any photo of this set-up?
I am trying to mod one of my FWAA with a TS10 V2 (slightly different from V1) driver but something is off.
I canāt get to make the connection work and Iām running out of ideas of what may be wrong.
Also, when the driver is installed and I make contact with the - negative wire on the mcpcb, it is giving some kind of short
Any help from you or from anyone that modded an FWAA with a TS10 driver is welcome
Thanks in advance!!!
Because the TS10ās driver is substantially thinner than the FWAAās driver,
I think that might be a double typo, and driver should say mcpcb
āBecause the TS10ās driver mcpcb is substantially thinner than the FWAAās driver mcpcb,ā
anyone that modded an FWAA with a TS10 driver
I dont think anybody has put a TS10 driver in a FWAAā¦
afaik the TS10 driver does not work w the FWAA tailswitch and body tubes, they are wired backwardsā¦
iow, the Fwaa inner outer body tube is negative, but the TS10 inner body tube is positive negative
edit: thanks to INeedMoreLumens for the corrected body tube polarity details
the Fwaa inner body tube is negative, but the TS10 inner body tube is positive
Iām not sure if this was changed in the TS10 v2 but on the TS10 v1 the inner tube is negative and on the FWAA the outer tube is negative.
This is correct. I wrote ādriverā when I meant to write āstarā.
The TS10 and FWAAās drivers are not easily swapped. My vague recollection is this is because the FWAA uses the interior tube for the switch and the exterior switch for main current. The TS10 is wired the opposite with the inner tube used for main current and the outer body for the switch.
This means that
a) I missed some crucial information along the time, regarding the incompatibility of these components of both flashlights
b) I ordered drivers to make a mod that wonāt happen
c) Firelight2ās post needs to be corrected to avoid further mistakes.
@jon_slider
Thank you very much for the clarification and explanation !! Always on spot my friend
@INeedMoreLumens
Thanks for confirming/correcting the information!
@Firelight2
Thanks for confirming the information above too.
As for your post, can you please correct it and name it accordingly so that other (unwary) people follow the same mistake? It would be much appreciated.
And for your words I assume that it is really almost impossible to use that driver on the FWAA host, right?
This said, is there any place or someone that sells āready to useā drivers for the FWAA that can be flashed (3 pins) without having to do a circus of programming wires and devices everywhere?
Thanks again for the help folks
is there any place or someone that sells āready to useā drivers for the FWAA that can be flashed (3 pins)
not that Im aware of
maybe ask thefreeman if he can find the time to build you one of his FWAA drivers
while you are waiting, consider buying a Wurkkos TS10
Zwerglein02 offers an mcpcb w RGB and 519a capabilityā¦ you might also be able to buy a modded TS10 from him.
@Firelight2
Thanks for confirming the information above too.
As for your post, can you please correct it and name it accordingly so that other (unwary) people follow the same mistake? It would be much appreciated.
And for your words I assume that it is really almost impossible to use that driver on the FWAA host, right?
Corrected the erroneous wording in my post to replace ādriverā with āstarā.
Using the TS10 driver on an FWAA host can probably be done, but I think the switch board would need to be rewired as you need the switch button to close the circuit on the outer channel not the inner one.
It might be possible to do this by using a TS10 switch board instead of an FWAA switch board, but I canāt be sure as I havenāt looked into this myself.
This said, is there any place or someone that sells āready to useā drivers for the FWAA that can be flashed (3 pins) without having to do a circus of programming wires and devices everywhere?
Thefreeman has made a very nice regulated FWAA driver, though it is quite complicated and hard to assemble.
Iāve been working on an FWAA-T1616 1+FET driver that attempts to use as many stock components as possible, only needing a new MCU and FET. It uses the TS10 hex file, though it might need some slight callibration, as the voltage fudge factor is different, so it would be reading 0.1v high
not that Im aware of
maybe ask thefreeman if he can find the time to build you one of his FWAA drivers
Thanks for the information @jon_slider In case I cannot mod the FWAA with the TS10 driver, I will consider asking thefreeman about his drivers! Good suggestion
while you are waiting, consider buying a Wurkkos TS10
I have 2 of them already, the TS10 has been my EDC for some months now, I got another on (v2) in the last weeks, and I want to get a new one to be trendy and mod into a single led light I really love the TS10!!!
Corrected the erroneous wording in my post to replace ādriverā with āstarā.
Using the TS10 driver on an FWAA host can probably be done, but I think the switch board would need to be rewired as you need the switch button to close the circuit on the outer channel not the inner one.
It might be possible to do this by using a TS10 switch board instead of an FWAA switch board, but I canāt be sure as I havenāt looked into this myself.
Thank you very much @Firelight2 , for the correction and for the suggestion!
It is a bit challenging to make it happen, because of the differences you and others mentioned (current and signal) but I am trying to make some progress with the TS10 switch!
It seems like it needs several steps to tune it perfectly, though! But that was a great tip and I will dig it further
Thefreeman has made a very nice regulated FWAA driver, though it is quite complicated and hard to assemble.
Thanks @YBF650 ! Assembling is a no-go for me since I have no tools and no expertise in doing so, hence my question about ready to use drivers.
In any case, I will proceed with my attemps with the drivers I have now, and if it fails, maybe I will resort to your and jon_sliderās suggestions !
Thank you all, once again!!
the TS10 has been my EDC for some months now
Very glad you have TS10 options.
I hope your FWAA project comes together also.
fwiw, Toykeeper has created new firware for it, using thefreemanās driver:
I was just reading the Anduril change log, it says:
2023-10-31 New lights:
thefreeman-boost-fwaa: Added. (1632) (very nice AA/li-ion HDR boost driver which fits into a FWAA)
I hope youre enjoying a beautiful Spring Time
Very glad you have TS10 options.
I really like this little light
I hope your FWAA project comes together also.
Thatās 2 of us, but it will depending on having spare switches of the TS10 V1. Letās see how it ends. Iāll post if/when I manage to do that Thanks for encouraging!
I hope youre enjoying a beautiful Spring Time
You too my friend
Seems like the rain is over now and temps will go higher in the next days, so spring is āre-arrivingā Enjoy and thanks for the support!